Manual

ManualsBrandsKEYENCE ManualsSensorsAP-C30KP

Ultra-compact Digital

Pressure Sensor

AP-C30K (P) Series

Instruction Manual

1. Safety Precautions

WARNING

●

Do not use this product in safety circuits such as those designed to

protect human workers.

●

This product does not employ an explosion-proof construction. Do not

use it in the presence of flammable gasses, liquids, or powders.

●

This is a direct current power supply type sensor. Application of an

alternating current may result in explosion or fire.

■ Accessories

???

96M1038

3. Pipe Connections

You can select from one of two pressure ports: one on the back of the

sensor that can accommodate a pipe leading directly away from the back

of the sensor, and one on the side of the sensor to accommodate a pipe

leading away from the sensor at a right angle.

1) The pressure port is 1/8 of NPT. Commercially available air pressure

joints and nipples can be used with the port.

When attaching the joint, use a wrench to hold the pressure port in

place as illustrated below.

Hold in place

with wrench

(12mm).

2) Attach the included valve plug to the pressure port not being used.

Hold in place with

wrench (12 mm).

Hexagonal

wrench (5mm)

Valve plug with

hexagonal hole

CAUTION

• Do not use a torque in excess of 10 Nm when tightening the joint.

Doing so may damage the joint.

• Apply sealing tape when attaching the joint in order to prevent air leaks.

4. Mounting Brackets (option)

Dedicated mounting hardware is available for the sensor, allowing it to be

installed in a range of locations.

Horizontal mounting bracket Wall mounting bracket

(AP-BO1) (AP-BO2)

Faceplate/ceiling mounting bracket Tilted mounting bracket

(AP-BO3) (AP-BO4)

Substitution bracket (AP-BO5)

* Distance between arms is same as the AP-30/40 Series brackets.

●

1 connector cable (2 m)

●

1 unit scale label

2. Part Names

SET AP-C33K MODE

MPa

Pressure display unit

*Apply the units sticker here.

Pressure display

Mode button

Manual adjustment button

Set button

Wiring

connector

Pressure

port (rear)

Pressure port

(side)

Mounting screws

(M3 x 2)

Operational indicator

Output 1 Output 2

1 2

Approx. ± 90°

●

1 valve plug with hexagonal hole

●

1 instruction

manual

Summary of content (5 pages)

PAGE 1
96M1038 ??? 3. Pipe Connections You can select from one of two pressure ports: one on the back of the sensor that can accommodate a pipe leading directly away from the back of the sensor, and one on the side of the sensor to accommodate a pipe leading away from the sensor at a right angle. 1) The pressure port is 1/8 of NPT. Commercially available air pressure joints and nipples can be used with the port. When attaching the joint, use a wrench to hold the pressure port in place as illustrated below.
PAGE 2
AP-AO1 Panel mounting bracket 7. Detection Mode Operation ■ General-purpose mode (F-1) This mode allows the user to configure 2 detection points. Control output 1: Turns ON when pressure exceeds setting P1. Control output 2: Turns ON when pressure exceeds setting P2. Panel mounting ring P2 P1 MP a 0 SE T Front protective cover 0 Output 1 AP -C 4303 OFF ON OFF OFF Output 2 ON OFF *Hysteresis is a standard 0.5% of F.S.
PAGE 3
8. Sensor Configuration ■ Toggling the display Current value + Peak hold + Reference value* Bottom hold After 4 sec of no key operation. ■ Mode configuration ■ Manual configuration Settings are manually configured. The display changes for each mode. * Toggling the display of settings (see the diagram below). * Manual configuration only during F-3/A2 mode operation. Increase the setting. Decrease the setting.
PAGE 4
Resetting the peak/bottom hold values/ Pressing for 3 seconds or more while the peak and bottom hold values are being displayed will reset the values. *The values will also be reset when power to the sensor is turned off, and when the device's detection mode or operating mode is changed. 9. Explanation of Features ■ Switching the detection range (AP-C30K(P) only) The AP-C30KP allows you to select a detection range. (When using Pa units) Pressure type Display Range Negative pressure 0 to -101.
PAGE 5
11. Ambient Pressure Compensation 14. Error Displays and Corrective Actions ■ Error displays during normal operation Open the applied pressure to the surrounding air so that it equals the ambient pressure and press the button for 3 seconds or more while the current value or reference value is being displayed. The ambient pressure point will be corrected. *1 Ambient pressure can be corrected within a range of ±5 % of F.S.