User guide

ManualsBrandsKEYENCE ManualsLightingCV-X290

This manual describes the hardware information. Read this manual

thoroughly to understand how the CV-X290 works in order to maximize

the performance of the system.

• Always keep this manual in a safe location for future reference.

• Please ensure that the manual is passed to the end user of the

controller.

Symbols

The following symbols alert you to important messages. Be sure to read

these messages carefully.

Trademarks

• "SD Memory Card" is a registered trademark of the SD Association.

• Other company names and product names noted in this document are

registered trademarks or trademarks of their respective companies.

The TM mark and ® mark are omitted in this manual.

Libraries and programs

libjpeg

This software is based in part on the work of the Independent

JPEG Group.

Introduction

It indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

It indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

It indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

It indicates a situation which, if not avoided, could result in

product damage as well as property damage.

It indicates cautions and limitations that must be followed during

operation.

It indicates additional information on proper operation.

It indicates tips for better understanding or useful information.

DANGER

WARNING

CAUTION

NOTICE

Important

Point

Reference

96M13191

High-speed, High-capacity

Machine Vision System

CV-X290

Controller Instruction Manual

Read this manual thoroughly before using the CV-X290.

Always keep this manual in a safe place for future reference.

Summary of content (8 pages)

PAGE 1
96M13191 High-speed, High-capacity Machine Vision System CV-X290 Introduction This manual describes the hardware information. Read this manual thoroughly to understand how the CV-X290 works in order to maximize the performance of the system. • Always keep this manual in a safe location for future reference. • Please ensure that the manual is passed to the end user of the controller. Symbols The following symbols alert you to important messages. Be sure to read these messages carefully.
PAGE 2
Package Contents The equipment and accessories listed below are included in the package when shipped. After opening the carton, check that you have received all of the equipment and accessories listed below.
PAGE 3
Identifying Controls and Connectors With CA-EC80L installed 햿Power and ground terminals Use to connect power (24 V DC) and the ground wire. 헀Expansion unit connector 2 (left side) Use to connect the illumination expansion unit CA-DC10E, CA-DC21E, or CA-DC30E. 헁CAMERA1 connector Use to connect the LJ-V as camera 1. Installing the Controller Unit Install the controller unit to DIN rail, or use the holes on the bottom of the controller to secure it with screws.
PAGE 4
Installing the Expansion Unit Installing the Camera Input Unit Installing the Camera Expansion Unit Install an optional camera input unit (the CA-EC80L for high-pixel cameras, the CA-EC80HX for HX Series cameras, the CA-EC80LJ for the LJ-V, or the CA-EC80 for area cameras) to the camera slot for the controller. Use a camera expansion unit CA-E800 (sold separately) to which a camera input unit has been connected in order to increase the number of cameras to connect.
PAGE 5
When connecting LJ-V with the camera input unit CA-EC80LJ (for LJ-V) attached Peripheral Device Peripheral Device LJ-V Series Controller (sold separately) A D-type ground (third ground) (ground resistance 100 Ω) Peripheral Device B A B A>B A
PAGE 6
Reference • COMOUT2 for Pin 17 and Pin 40 are common. • COMIN2 is a common terminal for input for the parallel I/O connector. • COMOUT2 is a common terminal for output for the parallel I/O connector. • Power source 0 V and COMIN1, COMIN2, COMOUT1, COMOUT2, COMOUT_F+, and COMOUT_F- are all isolated.
PAGE 7
Main Specifications Model name*1*2 CV-X290 Main processor for image processing With LJ-V connected • 512 (H) x 16384 (L), approx. 8,390,000 pixels • 1024 (H) x 8192 (L), approx. 8,390,000 pixels • 2048 (H) x 4096 (L), approx. 8,390,000 pixels With CA-HX500C/HX500M connected • 5,000,000-pixel mode: 2432 (H) x 2040 (V), approx. 4,960,000 pixels • 2,000,000-pixel mode: 1600 (H) x 1200 (V), approx. 1,920,000 pixels With CA-HX200C/HX200M connected • 2,000,000-pixel mode: 1600 (H) x 1200 (V), approx.
PAGE 8
Dimensions WARRANTIES AND DISCLAIMERS Controller Unit (CV-X290 + CA-EC80L) DIN-rail mount Depth: Depth: Depth: Depth: Unit: mm Controller Unit (CV-X290 + CA-EC80LJ) 134.6 23.5 132 6 83.3 65.3 153 35.9 DIN-rail mount (85) 116.7 M4 Depth:11.0 112 M4 Depth:11.0 (1) KEYENCE warrants the Products to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment.