Instruction Manual

ManualsBrandsKEYENCE ManualsSensorsSK-1000 Series

E SK-1000 IM

Simulation Mode

You can use this function to check that the I/O control cable has been wired

correctly.

Main screen

1 On the main screen, while pressing the

[MODE] button, press the W button five times.

[51.out] is displayed on the main display (upper

level).

While pressing

the [MODE]

button, press the

W button five

times.

2 Use the S/T buttons to display the signal that

you want to output in the sub display (lower

level). The signal will be output when it is

displayed. Press the [MODE] button to

proceed to the next step.

[MODE] button

3 When you turn ON external input 1 to external

input 4, the corresponding part of the display

will change from [_] to [o].

From the right, the parts correspond to external

inputs 1, 2, 3, and 4.

Press the [MODE] button to proceed to the next step.

(Example) [___o] indicates that external input 1 is

on.

[o_o_] indicates that external inputs 2

and 4 are on.

[MODE] button

4 The upper limit, middle value, and lower limit

of the analog output are generated. This is not

displayed when the analog output is turned

OFF. Press the [MODE] button to proceed to

the next step.

(Example) When the analog output setting is 0 to 5 V

5 V is output for Hi, 2.5 V is output for Mid,

0 V is output for Lo, and 5.5 V is output for

Err.

[MODE] button

5 [END] is displayed on the sub display (lower

level). Press the [MODE] button to complete

the procedure and return to the main screen.

HOLD

ALARM

BANK

ZERO SHIFT

TIMING

TEMP %RH

HI LO R.V.

off

51.out

Setting value Description

OFF No signal is output.

HI The HI signal is output.

GO The GO signal is output.

LO The LO signal is output.

ALM The alarm signal is output.

----

52.in

53.AnG

Setting

value

Description

The upper limit of the analog output is

generated.

Mid

The middle value of the analog output is

generated.

The lower limit of the analog output is

generated.

Err

The output value when an error occurs is

output.

HOLD

ALARM

BANK

ZERO SHIFT

TIMING

TEMP %RH

HI LO R.V.

Return to the

main screen.

5. Specifications

This chapter describes the specifications, circuit diagrams, and dimensions of the

SK Series.

Specifications

 Sensor head

*1 Even in the measurement area, if the distance to the detection target is smaller than the

reference distance, measurement cannot be performed up to the upper limit of the

measurement range.

*2 When measured an average of 256 times, this value is ±100 V or less in high-precision

mode and ±1 kV or less in wide-range mode, and ±10% (indicated value) in other ranges.

*3 The measurement accuracy range is ± 30 kV.

*4 At 25°C and with a humidity of 50%RH

*5 OP-87934 is necessary.

*6 This is when ±100 V or less, and ±10% (indicated value) in other ranges.

 Sensor amplifier

*1 Select one from ±5 V, 1-5 V, 0-5 V, 4-20 mA.

*2 The four external input wires are assigned to arbitrary inputs.

Rated novoltage input: ON voltage of 2 V or less, OFF current of 0.02 mA or less.

Rated voltage input: max. input rating of 30 V or less, ON voltage of 7.5 V or more, OFF

current of 0.05 mA or less.

*3 Rated NPN open-collector output: max. 50 mA/ch (20 mA/ch when expansion units are

connected), 30 V or less, residual voltage of 1 V or less (1.5 V or less when five or more

expansion units are connected).

Rated PNP open-collector output: max. 50 mA/ch (20 mA/ch when expansion units are

connected), supply voltage or less, residual voltage of 2 V or less (2.5 V or less when five or

more expansion units are connected).

*4 Power supply voltage of 20-30 V when five or more expansion units are connected.

*5 Max. 11.3 W when eight units and the DL Series are connected.

Model SK-050

Electrification

potential

measurement

Measurement mode High precision Wide range

Reference distance for

measurement

25 mm 100 mm

Measurement distance 5 to 50 mm 60 to 120 mm

Measurement range

±2 kV ±50 kV

Measurement accuracy

±10 V ±100 V

Sampling time Approx. 1.4 ms

Temperature

measurement

Measurement range 0 to 50°C

Measurement accuracy

±1°C

Minimum display unit 0.1°C

Sampling time 1 s

Humidity

measurement

Measurement range 10 to 85% RH

Measurement accuracy

±5% RH

Minimum display unit 0.1% RH

Sampling time 1 s

Ion balance

measurement

mode

Ion balance measurement

range

±1 kV

Measurement accuracy

±10 V

Minimum display unit 1 V

Environmental

resistance

Ambient temperature 0 to 50°C (no freezing and no condensation)

Ambient humidity 10 to 85%RH (no condensation)

Materials Main body case: PC, metal part: SUS, cable: PVC

Weight Approx. 35 g

Model SK-1000 SK-1050

Type Mounting DIN rail.

Main unit/expansion unit Main unit Expansion unit

Display

Minimum display unit 0.001 kV

Display range ±99.999 kV to 99 kV (Four-stage selection possible)

Analog voltage output

±5 V, 1-5 V, 0-5 V,

Load resistance: 100Ω

–

Analog current output

4 to 20 mA

max. load resistance 350Ω

Control

input

Zero shift input

No-voltage input

Timing input

Reset input

Bank input

Control

output

Judgment output

Open-collector output

(NPN/PNP switchable; NO/NC switchable)

Alarm output Open-collector output (NPN/PNP switchable, N.C.)

Power

supply

Supply voltage

10 to 30 VDC including

10% ripple (P-P)

Supplied from the main

unit.

Current consumption

(Excluding the load

current of each output.)

1650 mW or less

(at 30 V, 55 mA max)

1170 mW or less

(at 30 V, 39 mA max)

Environmental

resistance

Ambient temperature 0 to 50°C (no freezing and no condensation)

Ambient humidity 10 to 85%RH (no condensation)

Materials

Main body case / front cover: PC, key top: POM,

cable: PVC

Weight (Including accessories) Approx. 150g Approx. 140g