SELECTION GUIDE InfiniiVision Oscilloscope Probes and Accessories For 1000 X-, 2000 X-, 3000A/T X-, 4000 X-, 6000 X-, 5000, 6000, and 7000 Series
Introduction To achieve the best results from your scope, you need the right probes and accessories for your particular application. That is why Keysight Technologies, Inc. offers a complete family of innovative probes and accessories for InfiniiVision oscilloscopes. For the most up-to-date and complete information about Keysight’s accessories, please visit our Web site at: www.keysight.
Probe Compatibility Table For ordering information when replacing your probe or probe accessory: Refer directly to the page number listed in the Table of Contents for your probe model. To assist you in selecting the proper probe for your application: Use our probe compatibility table below to find the probes that are recommended for use with your 1000 X-, 2000 X-, 3000A/T X-, 4000 X-, 6000 X-, 5000, 6000, and 7000 Series InfiniiVision oscilloscope.
Probe Compatibility Table (Continued) Probe type Probe model DSO5000A 100 MHz DSO5000A 300 to 500 MHz MSO/DSO6000A 4 100 MHz MSO/DSO6000A 4 300 MHz to 1 GHz MSO/DSO7000A/B 100 MHz to 1 GHz Passive probes, page 5 N2863B 10:1 300 MHz (included in 5000 Series 100/300 MHz) 10070D 1:1 20 MHz Recommended Recommended Recommended Compatible Recommended Recommended Recommended Recommended 10073D 10:1 500 MHz (included in 6000/7000 Series 300 MHz to 1 GHz and 5000 Series 500 MHz) 10074D 10:1 150 MHz (
Passive Probes –– Designed for optimal performance with your Keysight InfiniiVision Series oscilloscopes –– 1:1 and 10:1 attenuation ratio –– 20 to 700 MHz Rugged, high-quality probes at a reasonable price Keysight 10070-family passive probes are a great choice if you are looking for high quality at a very reasonable price. These general-purpose probes are designed specifically to give you optimal performance with your InfiniiVision Series oscilloscopes.
Passive Probes (Continued) Accessories available for 10070D/73D/74D passive probes N4848A 5081-7696 N4847A N4849A 5081-7690 10072A 10075A Probe-tip-to-BNC (m) adapter, qty 2 Ground lead with alligator clip for 1007x and N2862B/63B/89A/90A Retractable hook tip for 1007xC/D (not compatible with 10076A/B), qty 2 Dual-test lead adapter (for 10070/3/4x), qty 2 Replacement parts accessory kit Fine-pitch probing kit includes 10 SMT clips and 2 dual-lead adapters 0.5 mm IC probing kit. Contains 4 0.
Passive Probes (Continued) Ordering information for Keysight passive probes N2142A N2140A 10070D N2840A N2862B/N2841A N2853A 10074D N2863B/N2842A N2889A 10073D N2890A/N2843A N2873A N2894A N7007A 10:1/1:1 75 MHz passive probe 10:1/1:1 200 MHz passive probe 1:1 20 MHz passive probe 10:1 50 MHz passive probe 10:1 150 MHz passive probe 10:1 350 MHz passive probe (2 m cable) 10:1 150 MHz passive probe 10:1 300 MHz passive probe 10:1/1:1 350 MHz passive probe 10:1 500 MHz passive probe 10:1 500 MHz passive probe
Passive Probes (Continued) Characteristics for Keysight passive probes Bandwidth Risetime (calculated) Attenuation ratio Input resistance Input capacitance Maximum input (dc + peak ac) Compensation range Probe readout Cable length 10070D 20 MHz < 17.5 ns 1:1 1 MΩ Approx 70 pF 300 Vpk mains isolated 150 Vpk CAT II None Yes 1.5 m Attenuation ratio Input resistance N2862B,41A/ N2863B,42A 150 MHz/ 300 MHz < 2.33 ns/ < 1.
Extreme Temperature Passive Probe Features and specifications –– Wide operating temperature range of –40 to +85 °C for extreme temperature environmental chamber testing –– 400 MHz bandwidth (–3 dB) –– High impedance (10 MΩ at DC) input –– Wide input range: 1 kV CAT II, 600 V CAT III –– Includes hook tip adapters (x2), ground leads (x2) and spring ground tip (x1) The N7007A 400 MHz passive probe is a low-cost, high impedance passive probe with rugged probe tips for environmental chamber testing from –40 to +
High-voltage Passive Probes –– Ideal for measuring up to 3.7 kV –– Up to 500 MHz bandwidth –– 100:1 attenuation 10076C high-voltage probe The Keysight 10076C 3.7 kV 100:1 passive probe gives you the voltage and bandwidth you need for making high-voltage measurements. Its compact design makes it easier to probe today’s small power electronics components and its rugged construction means it can withstand rough handling without breaking.
InfiniiMax Active Probes and Accessories 1130B-34B InfiniiMax high-performance active probe system –– 1.
InfiniiMax Active Probes and Accessories (Continued) 1130B-34B InfiniiMax high-performance active probe system Ordering information for Keysight InfiniiMax 1130B Series probe and accessories Probe amplifier 1130B 1131B 1132B 1134B Connectivity kits E2669B E2668B Individual probe heads E2675B E2676B E2677B E2678B E2679B N2851A N2849A N5380B N5425B/N5426A N5451A N5450B N2880A N2881A 1.5 GHz InfiniiMax probe amplifier (order one or more probe heads or connectivity kits per amplifier) 3.
InfiniiMode Active Probes and Accessories N2750A-52A InfiniiMode probe –– 1.
InfiniiMode Active Probes and Accessories (Continued) Characteristics and specifications for N2750A Series InfiniiMode probes Model number Probe bandwidth 1 (–3 dB) Rise time, probe only (10 to 90%) Input resistance (at DC) 1 Input capacitance Attenuation ratio (at DC) Input dynamic range Input common mode range Offset range Offset accuracy 2 Maximum non-destructive input voltage Maximum number of probes supported by 3000 X-Series Maximum number of probes supported by 4000 X-, 6000 X-Series N2750A 1.
High-voltage Differential Active Probes –– 25 to 800 MHz bandwidth –– High common mode rejection ratio –– Measure up to 1,400 V CAT II and 7 kV mains isolated N2790A/91A and N2891A high voltage differential probes Oscilloscope users often need to make floating measurements where neither point of the measurement is at earth ground. Use N2790A, N2791A, or N2891A high voltage differential probes to make safe and accurate floating measurements with an oscilloscope.
High-voltage Differential Active Probes (Continued) N7013A extreme temperature extension cable kit The N7013A is a 70-cm long extreme temperature extension cable kit compatible with four of Keysight’s medium- and high-voltage differential active probes, including the N2790A, N2791A, N2792A, and N2818A. These probes are typically used in power supply testing applications, as well as testing automotive differential buses including CAN, CAN FD, and FlexRay.
High-voltage Differential Active Probes (Continued) N2804A/N2805A high-voltage, high-speed differential probes The N2804A and N2805A differential probes provide the superior general-purpose differential signal measurements that are required for high-speed power measurements such as measuring characteristics of switching power devices, DC-DC converters or class D amplifiers, vehicle bus measurements, and high-speed digital system designs.
High-voltage Differential Active Probes (Continued) N2792A/N2818A 200-MHz and N2793A/N2819A 800-MHz general-purpose differential probe The N2792A/N2818A 200-MHz and N2793A/N2819A 800-MHz differential probes provide the superior general-purpose differential signal measurements required for today’s high-speed power measurements, vehicle bus measurements, and digital system designs.
Single-ended Active Probes N2795A/96A/97A low-cost single-ended active voltage –– High resistance (1 MΩ) and low capacitance (1 pF) input for low loading –– Wide input dynamic range (± 8 V) and offset range (± 12 V for N2796A/97A, ± 8 V for N2795A) –– Built-in headlight –– Direct connection to AutoProbe interface (no power supply required) –– N2797A for extreme temperature environmental chamber testing at –40 to +85 °C The N2795A/96A are a new generation of low-cost, 1 to 2 GHz single-ended active probes w
Single-ended Active Probes (Continued) N7020A power rail probe –– 2-GHz single-ended active probe for power rail noise measurement –– 1.1:1 attenuation ratio ensures low noise signal measurement –– ± 24 V of probe offset range enables effective elimination of DC component of a power supply. The N7020A power rail probe is a low noise, large offset range oscilloscope probe that enables users to measure small signals riding on top of DC power rails.
Mixed Signal Oscilloscope Logic Probes –– Compatible with all 40-pin logic probes –– Flying leads offer flexibility and convenience MSO probes offer great value and performance These logic probes for the InfiniiVision mixed signal oscilloscopes (MSOs) are the same ones used with Keysight industry- leading high-performance logic analyzers. This means we can offer the best performance, great value, and access to the industry’s broadest range of logic probing accessories.
Mixed Signal Oscilloscope Logic Probes (Continued) The InfiniiVision MSO digital channels were designed to be compatible with a wide variety of probing accessories developed over 20 years for logic analyzers. There is a good chance that the logic analyzer accessories you already own work with your MSO.
Clamp-on Current Probes –– Up to 150 MHz bandwidth and 500 Arms current measurement range –– Hybrid technology to measure ac and dc –– Compatible with 1 MΩ scope input Accurate current measurements without breaking the circuit Compatible with any scope or voltage measuring instruments with BNC input, the 1146B and N2780B Series current probes offer accurate and reliable solutions for measuring dc and ac currents.
Clamp-on Current Probes (Continued) N7026A high sensitivity clampon current probe 1 mA/div sensitivity The N7026A is the Keysight’s highest sensitivity clamp-on current probe. It has up to 5x lower noise than our other clamp-on current probes with 0.1V/A output voltage rate. This enables you to measure down to 1 mA/div with much higher accuracy. The N7026A, when used with an InfiniiVision or Infiniium oscilloscope, provides highly-accurate, low current waveforms for improved debug and analysis.
Clamp-on Current Probes (Continued) Characteristics of the 1146B current probe Bandwidth 1 Current range 1 dc to 100 kHz (–3 dB) 100 mV/A:100 mA to 10 A peak 10 mV/A:1 to 100 A peak 1000 mV peak max Output signal 1 AC current accuracy Range 100 mV/A (50 mA to 10 A peak) Accuracy 3% of reading ± 50 mA Range 10 mV/A (500 mA to 40 A peak) Accuracy 4% of reading ± 50 mA Range 10 mV/A (40 A to 100 A peak) Accuracy (40 A to 100 A peak) 15% max at 100 A Noise Range 10 mV/A: 480 μV Range 100 mV/A: 3 mV Insertion
Clamp-on Current Probes (Continued) Characteristics of the 1147B/N2893A/N7026A current probes Bandwidth (–3 dB) Rise time (calculated, 10% to 90%) Maximum current (continuous) Maximum peak current (non-continuous) (for pulse-widths ≤ 10 µs) Output voltage rate Minimum oscilloscope vertical scale Amplitude accuracy Noise Temperature coefficient for sensitivity Effect of external magnetic fields Maximum rated power Maximum input voltage Diameter of measurable conductors Probe interface Cable lengths Maximum
N7040A/41A/42A Rogowski Coil AC Current Probes –– Easy-to-use clip-around coil enabling current measurement in confined space –– Measure AC current up to 3,000 Apk (with N7040A) –– Up to 30 MHz bandwidth (with N7041A/42A) The N7040A Series Rogowski coil current probes are designed for measuring AC currents ranging from a few 100 milliamps to 3,000 A from 3 Hz to > 30 MHz.
High-sensitivity Current Probes –– Measure AC/DC currents as low as 50 µA –– Ideal for capturing and analyzing low level current flow in the DUT to characterize sub-circuits or measure current consumption of batterypowered devices or integrated circuits –– Simultaneous high- and low-gain views of the current waveform for more precise wide dynamic range measurement (with N2820A) Use an area-under-the-curve measurement (Charge) on InfiniiVision oscilloscopes to easily calculate the integrated current consump
High-sensitivity Current Probes (Continued) Probe characteristics and specification Bandwidth (–3 dB) Risetime (Tr = 0.35/bandwidth, 10 to 90%) Minimum measurable current 1 Maximum measurable current DC amplitude accuracy Gain 3 Max input voltage Output impedance Standard accessories Compatible InfiniiVision oscilloscopes Max number of probes supported by 3000 X-Series Max number of probes supported by 4000 X-Series Zoom-out channel: DC to 3 MHz Zoom-in channel: DC to 500 kHz Zoom-out channel: < 0.
Wedge Probe Adapters –– Easy connection to surface mount ICs –– Safe, with no chance of shorting –– Mechanically non-invasive contact –– 3-, 8-, and 16-signal versions –– Supports 0.5 and 0.65-mm –– TQFP and PQFP packages Problem-free probing The Keysight wedge probe adapter eliminates many of the frustrations associated with probing surface mount components.
Miscellaneous Accessories Testmobile Carrying cases Rackmount kit The sturdy Keysight 1180CZ Testmobile for use with 6000 Series oscilloscopes makes sharing your scope easy. Its large wheels make it easy to roll from place to place. For use with the Keysight 6000 Series scope, the 1180CZ Testmobile scope cart with the N2919A bracket provides convenient mobility and secure mounting of your scope.
Miscellaneous Accessories (Continued) Probe positioners –– Easy-to-manipulate probe arms for hands-free browsing –– One- or two-articulated arms with stable high-mass base (N2784A and N2785A) –– Quick and stable XY positioning (N2786A) –– Stable 3D probe positioning for hard-to-reach XYZ access (N2787A –– Compatible with most scope probes –– Applications: Hands-free browsing for electronic components on PC board Ordering information Product number N2784A 1 N2785A 1 N2786A N2787A 1.
T2A Probe Interface Adapter –– Enables Tektronix TekProbe-BNC level 2 probes to connect to Keysight’s AutoProbe interface on InfiniiVision 3000 X-, 4000 X-, 6000 X-, 5000, 6000, and 7000 oscilloscopes –– An easy-to-use plug-on adapter to the Keysight oscilloscope’s AutoProbe interface –– Provides necessary probe power, calibration, and offset control as needed to the attached TekProbe probe The N2744A T2A interface adapter enables selected TekProbe interface level 2 probes to be used with Keysight oscillosc
Recommended Probes for Low-/Mid-speed Bus Measurements Applications LIN ARINC 425 CAN MIL-STD 1553 I²S (audio) I²C/SMbus RS232/UART RS422/485 FlexRay SPI MOST USB 2.0 Speed and signal type 10 kHz, single-ended 1000 kbps, differential 1 Mbps, differential 1 Mbps, differential ± 25 Vpp ~2.8 MHz, single-ended < 4 MHz, single-ended < 10 Mbps, single-ended 10 Mbps, differential 10 Mbps, differential 1 to 100 MHz, single-ended 150 Mbps, differential 480 Mbps, differential Find us at www.keysight.
Keysight Oscilloscopes Multiple form factors from 20 MHz to > 90 GHz | Industry leading specs | Powerful applications Learn more at: www.keysight.com For more information on Keysight Technologies’ products, applications or services, please contact your local Keysight office. The complete list is available at: www.keysight.com/find/contactus Find us at www.keysight.com This information is subject to change without notice.
