Datasheet

Page 13
Find us at www.keysight.com
Ordering information for
InfiniiMode probes and
accessories
N2750A 1.5 GHz InfiniiMode differential
probe
N2751A 3.5 GHz InfiniiMode differential
probe
N2752A 6 GHz InfiniiMode differential probe
N2776A Differential browser tips (qty 3)
N2777A InfiniiMode solder-in tips (qty 3)
N2778A InfiniiMode socketed tips (qty 3)
N4822A Socketed tip for USB/Ethernet
application fixtures (qty 1)
Each probe includes two solder-in tips,
two socketed tips and two browser tips.
InfiniiMode Active Probes and Accessories
N2750A-52A InfiniiMode probe
– 1.5 to 6 GHz bandwidth
– Dual attenuation ratio (2:1/10:1)
– InfiniiMode probing for making
differential, single-ended and
common mode measurements with a
single probe
– Built-in quick action scope control
for quick access to a variety of scope
functions
– Built-in headlight
– Includes solder-in, browser, and
socketed tips standard
– AutoProbe interface for auto
configuration and probe power
The N2750A Series InfiniiMode differential
probe is a new generation of low-cost,
differential active probe compatible with
InfiniiVision 3000 X-, 4000 X-, 6000
X-Series and Infiniium oscilloscope’s
AutoProbe interface.
Measurement versatility
The N2750A Series InfiniiMode probe
offer 2:1 and 10:1 dual attenuation
settings, allowing them to be used for
a broad range of applications. Dual
attenuation range is automatically
configured depending on the size of the
input signal.
The new differential probe has an input
resistance of 200 kΩ (differential) or
100 kΩ (each input to ground), and an
extremely low input capacitance of 700 fF
to minimize circuit loading.
This, accompanied with superior signal
fidelity, makes these probes useful
for most digital design and debug
applications. And with their wide dynamic
range (10 Vpp) and offset range (± 15 V),
these probes can be used in a wide
variety of analog signal measurements as
well.
InfiniiMode usability
The N2750A comes with new InfiniiMode
operation modes. The InfiniiMode allows
convenient measurements of differential,
single-ended, and common mode
signals with a single probe tip without
reconnecting the probe to change
the connection. The N2750A probe’s
InfiniiMode provides the following modes
of operation.
– A – B (differential),
– A – ground (single-ended A)
– B – ground (single-ended B)
– (A+B)/2 – ground (common mode)
Quick action scope control
The N2750A Series InfiniiMode probe
provides convenient and quick access
to various functions on the scope. You
often have a need to control the scope
while you hold a probe in your hand. With
the quick action scope control feature
built into the probe, you can turn the
built-in headlight of the probe on and off,
or control some frequently used scope
functions such as RUN/STOP, auto scale,
quick print, and quick save with only a
button press on the probe. Get control of
your most needed function with a push
of the quick action control button on the
probe.
Flexibility in probe use models is also a
vital necessity. The probes come standard
with three different types of exchangeable
probe tips that allow for easy connections
to the circuit under test. These probe tips
enable you to access multiple signals
on anything from header connectors to
hard-to-reach, high-density circuitry. The
probes are equipped with a white LED
headlight to illuminate the circuit under
test which will help you see where you are
probing.
This probe is compatible with InfiniiVision
3000 X-Series with software ver. 2.2 or
above, 4000 X-Series with software ver.
3.01 or above, and 6000 X-Series with
software ver. 6.00.