Datasheet

10 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
InniiMode Active Probes
and Accessories
N2750A-52A InniiMode probe
– 1.5 - 6 GHz bandwidth
– Dual attenuation ratio (2:1/10:1)
– InniiMode probing for making
differential, single-ended and
common mode measurements with a
single probe
– Built-in quick action scope control
for quick access to a variety of scope
functions
– Built-in headlight
– Includes solder-in, browser, and
socketed tips standard
– AutoProbe interface for auto
conguration and probe power
N2750A 1.5 GHz InniiMode
differential probe
N2751A 3.5 GHz InniiMode
differential probe
N2752A 6 GHz InniiMode
differential probe
N2776A Differential browser tips
(qty 3)
N2777A InniiMode solder-in tips (qty 3)
N2778A InniiMode socketed tips (qty 3)
N4822A Socketed tip for USB/
Ethernet application xtures
(qty 1)
The N2750A Series InniiMode differential
probe is a new generation of low-cost,
differential active probe compatible with
InniiVision 3000 X-, 4000 X-, 6000
X-Series and Inniium oscilloscope’s
AutoProbe interface.
Measurement versatility
The N2750A Series InniiMode probe offer
2:1 and 10:1 dual attenuation settings,
allowing them to be used for a broad
range of applications. Dual attenuation
range is automatically congured
depending on the size of the input signal.
The new differential probe has an input
resistance of 200 kΩ (differential) or 100
kΩ (each input to ground) and an
extremely low input capacitance of 700 fF
to minimize circuit loading.
This, accompanied with superior signal
delity, makes these probes useful for
most digital design and debug
applications. And with their wide dynamic
range (10 Vpp) and offset range (±15 V),
these probes can be used in a wide variety
of analog signal measurements as well.
InniiMode usability
The N2750A comes with new InniiMode
operation modes. The InniiMode allows
convenient measurements of differential,
single-ended, and common mode signals
with a single probe tip without
reconnecting the probe to change the
connection. The N2750A probe’s
InniiMode provides the following modes
of operation.
– A – B (differential),
– A – ground (single-ended A)
– B – ground (single-ended B)
– (A+B)/2 – ground (common mode)
Quick action scope control
The N2750A Series InniiMode probe
provides convenient and quick access to
various functions on the scope. You often
have a need to control the scope while you
hold a probe in your hand. With the quick
action scope control feature built into the
probe, you can turn the built-in headlight
of the probe on and off, or control some
frequently used scope functions such as
RUN/STOP, auto scale, quick print, quick
save, etc. with only a button press on the
probe. Get control of your most needed
function with a push of the quick action
control button on the probe.
Flexibility in probe use models is also a
vital necessity. The probes come standard
with three different types of exchangeable
probe tips that allow for easy
connections to the circuit under test.
These probe tips enable you to access
multiple signals on anything from header
connectors to hard-to-reach, high-density
circuitry. The probes are equipped with
a white LED headlight to illuminate the
circuit under test which will help you see
where you are probing.
This probe is compatible with InniiVision
3000 X-Series with software ver 2.2 or
above, 4000 X-Series with software ver
3.01 or above, and 6000 X-Series with
software ver. 6.00.
Ordering information for
InniiMode probes and
accessories
Each probe includes two solder-in tips, one
socketed tip and one browser tip.