Datasheet

20 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Bandwidth* dc to 100 kHz (–3 dB)
Current range* 100 mV/A:100 mA to
10 A peak
10 mV/A:1 to 100 A peak
Output signal 1000 mV peak max
AC current
accuracy*
Range 100 mV/A
(50 mA to 10 A peak)
Accuracy
Range
3% of reading ±50 mA
10 mV/A
(500 mA to 40 A peak)
Accuracy
Range
4% of reading ±50 mA
10 mV/A
(40 A to 100 A peak)
Accuracy (40 A to 100 A peak)
15% max at 100 A
Noise Range 10 mV/A: 480 μV
Range 100 mV/A: 3 mV
Insertion impedance 0.01 Ω (50/60 Hz)
Maximum working
voltage
600 Vrms CAT II or
300 Vrms CAT III
Maximum common
mode voltage
600 Vrms CAT II or
300 Vrms CAT III
Inuence of adjacent
conductor
< 0.2 mA/A AC
Inuence of
conductor position
< 0.2 mA/A AC
Battery 9 V alkaline (NEDA
1604A, IEC 6LR61)
Low battery Green LED on when
≤ 6.5 V
Battery life 55 hours typical
Bandwidth
(–3 dB)
dc to 50 MHz (1147B)
dc to 100 MHz (N2893A)
Risetime 7 ns or less (1147B), 3.5 ns
or less (N2893A)
Maximum
current
(continuous)
15 A peak, 15 A DC,
10 Arms (when two probes
are used with InniiVision
scope)
30A peak, 30 A DC, 24 Arms
(when one probe is used
with InniiVision 3000X,
5000/6000/7000 scope)
Maximum peak
current
(non-continuous)
30 A peak (when two probes
are used with InniiVision
scope) 32 A peak (when one
probe is used with
InniiVision scope)
Output voltage
rate
0.1 V/A
Amplitude
accuracy
±1% rdg, ±10 mA (dc and 45
to 66 Hz, rated current)
Noise Equivalent to 2.5 mArms or
less (for 20 MHz bandwidth
measuring instrument)
Temperature
coefcient for
sensitivity
±2% or less (within a range
of 0 to 40 °C or 32 to 104 °F)
Effect of
external
magnetic elds
Equivalent to a
maximum of 20 mA (in a dc
to 60 Hz, 400 A/m magnetic
eld)
Maximum rated
power
3 VA (with rated
current)
Maximum input
voltage
300 V CAT I
Diameter of
measurable
:conductors
5 mm dia. (0.2 in dia.)
Probe interface AutoProbe interface
Cable lengths Sensor cable:
Appox. 1.5 m (59.0n in)
Power supply cable:
Appox. 1 m (39.4 in)
Maximum
number of
probes
supported
2
Bandwidth (–3 dB) dc to 2 MHz (N2780B)
dc to 10 MHz (N2781B)
dc to 50 MHz (N2782B)
dc to 80 MHz (N2783L)
dc to 100 MHz (N2783A)
Maximum current
(continuous)
500 A (N2780B)
150 A (N2781B)
30 A (N2782B/83B/83L)
Maximum peak
current (non-
continuous)
700 A peak (N2780B)
300 A peak (N2781B)
50 A peak
(N2782B/83B/83L)
Maximum input
voltage
300 V CAT I
(N2782B/83B/83L)
300 V CAT III, 600 V
CAT II (N2780B/81B)
Output voltage rate 0.01 V/A
(N2780B/81B)
0.1 V/A
(N2782B/83B/83L)
Amplitude accuracy ±1.0 % rdg ±500 mA
(N2780B)
±1.0 % rdg ±100 mA
(N2781B)
±1.0 % rdg ±10 mA
( N2782B)
±1.0 % rdg ±10 mA
(N2783B/83L)
1146B 100-kHz current probe
1147B 50-MHz current probe with
AutoProbe interface
N2893A 100-MHz current probe with
AutoProbe interface
N2780B 2-MHz current probe
N2781B 10-MHz current probe
N2782B 50-MHz current probe
N2783L 80-MHz current probe with
5 m long cable
N2783B 100-MHz current probe
N2779A 3-channel power supply for
N2780B/81B/82B/83B/83L
Clamp-on Current Probes (continued)
Characteristics of the 1146B
current probe
Characteristics of the 1147B/
N2893A current probe
Characteristics of N2780B
Series current probes
Ordering information for
Keysight current probes
Note: Reference conditions 23 ±5 °C,
(73.4 ±41 °C) 20 to 75% relative humidity, dc to 1
kHz, probe zeroed, 1-minute warmup, batteries at
9 V + 0.1 V, external magnetic eld <40 A/m, no dc
component, no external current carrying
conductor, 1 MΩ/100 pF load, conductor centered
in jaw.
* Characteristics marked with asterisks are
specied performance. Others are typical
characteristics.
For more information about the N2780B
Series current probes, refer to the Keysight
N2780B Series current probe data sheet,
literature number 5989-6432EN.
Note: The above specications are guaranteed at
23 ±3 °C (or 73 ±5 °F)