Datasheet

ManualsBrandsKeysight ManualsOscilloscopesPC Oscilloscope, 2x 500MHz, 2.5GSPS

15 | Keysight | Streamline Series P924xA USB Oscilloscopes - Data Sheet

Trigger type selections

P9241A P9242A P9243A

Zone touch trigger Trigger on user-defined zones drawn on the display. Applies to one analog channel at a time. Specify zones as either “must

intersect” or “must not intersect.” Up to two zones. > 200,000 scans/sec update rate

Supported modes: normal, peak detect, high resolution

Also works simultaneously with the serial trigger and mask/limit test

Edge Trigger on a rising, falling, alternating or either edge of any source

Edge then edge (B trigger) Arm on a selected edge, wait a specified time, then trigger on a specified count of another selected edge

Pulse width Trigger on a pulse on a selected channel, whose time duration is less than a value, greater than a value, or inside a time

range

Minimum duration setting: 2 ns (500 MHz, 1 GHz), 6 ns (200 MHz)

Maximum duration setting: 10 s

Range minimum: 10 ns

Runt Trigger on a position runt pulse that fails to exceed a high level threshold. Trigger on a negative runt pulse that fails to

exceed a low level threshold. Trigger on either polarity runt pulse based on two threshold settings. Runt triggering can

also be time-qualified (< or >) with a minimum time setting of 2~10 ns and maximum timesetting of 10 s

Minimum time setting: 6 ns (200 MHz), 2 ns (500 MHz, 1 GHz)

Setup and hold Trigger and clock/data setup and/or hold time violation. Setup time can be set from –7 to 10 s. Hold time can be set from

0 s to 10 ns

Rise/fall time Trigger on rise-time or fall-time edge speed violations (< or >) based on user-selectable threshold

Select from (< or >) and time settings range between

Minimum: 1 ns (500 MHz, 1 GHz), 3 ns (200 MHz)

Maximum: 10 s

edge burst Trigger on the Nth (1 to 65535) edge of a pulse burst. Specify idle time (10 ns to 10 s) for framing

Pattern Trigger when a specified pattern of high, low and don’t care levels on any combination of analog or trigger channels is

[entered | exited]. Pattern must have stabilized for a minimum of 2 ns to qualify as a valid trigger condition

Minimum duration setting: 2 ns (500 MHz, 1 GHz), 6 ns (200 MHz)

Maximum duration setting: 10 s

Range minimum: 10 ns

Or Trigger on any selected edge across multiple analog channels

Video Trigger on all lines or individual lines, odd/even or all fields from composite video or broadcast standards (NTSC, PAL,

SECAM, PAM-M)

Enhanced Video (optional) Trigger on lines and fields of enhanced and HDTV standards (480p/60, 567p/50, 720p/50, 720p/60, 1080p/24,

1080p/25, 1080p/30, 1080p/50, 1080p/60, 1080i/50, 1080i/60)

C (optional) Trigger at a start/stop condition or user defined frame with address and/or data values. Also trigger on missing acknowl-

edge, address with no accq, restart, EEPROM read, and 10-bit write

RS-232/422/485/UART

(optional)

Trigger on Rx or Tx start bit, stop bit or data content or parity error

CAN (optional) Trigger on CAN (controller area network) version 2.0A,2.0B, and CAN-FD (flexible data-rate) signals. Trigger on the start of

frame (SOF), the end of frame (EOF), data frame ID, data frame ID and data (non-FD), data frame ID and data (FD), remote

frame ID, remote or data frame ID, error frame, acknowledge error, from error, stuff error, CRC error, spec error (ack or

form or stuff or CRC), all errors, BRS bit (FD), CRC delimiter bit (FD), ESI bit active (FD), ESI bit passive (FD), overload

frame., message, message and signal (non-FD), message and signal (FD, first 8 bytes only)

LIN (optional) Trigger on LIN (local interconnect network) sync break, sync frame ID, or frame ID and data, parity error, checksum error,

frame (symbolic), frame and signal (symbolic)

MIL-STD 1553 (optional) Trigger on MIL-STD 1553 signals based on word type (data or command/status), remote terminal address, data and errors

(parity, sync, Manchester encoding)

ARINC 429 (optional) Trigger and decode on ARINC429 data. Trigger on word start/stop, label, label + bits, label range, error conditions (parity,

word, gap, word or gap, all), all bits (eye), all 0 bits, all 1 bits

Performance Characteristics (Continued)