KSTAP05PHA KSTAP07PHA Read this owner’s manual thoroughly before operating the appliance and keep it handy for reference at all times.
Producto
Keystone. Keystone. 800-849-1112 keystonecs@keystone-products.com Keystone. 800-849-1112 keystonecs@keystone-products.com Keystone.
Troubleshooting Tips Read This Manual Inside you’ll find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner. You’ll find many answers to common problems in the troubleshooting tips - you should be able to fix most of them quickly before calling service.
Control panel Horizontal louver control lever(adjust manually) Air filter Vertical louver control lever (adjust manually) Upper air intake Panel Lower air intake Caster FRONT Handle (both sides) Drain outlet air outlet Bottom tray drain outlet REAR Design Notice: In order to ensure the optimal performance of our products, the design specifications of the unit and remote control are subject to change without prior notice.
Please read through these instructions before you start the installation process. Improper installation can cause damage to the unit, your personal property, and also poses a personal safety hazard. - DO NOT install your air conditioner in a wet room such as a bathroom or laundry room. Too much exposure to water can cause electrical components to short circuit. - DO NOT install the unit in a location that may be exposed to combustible gas, as this could cause a fire.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. - Children should be supervised to ensure that they do not play with the appliance.
19.7 inch ch 1 in 9.7 19.7 inch Your installation location should meet the following requirements: - Make sure that you install your unit on an even surface to minimize noise and vibration. - The unit must be installed near a grounded outlet, and the Collection Tray Drain (found on the back of the unit) must be accessible. - The unit should be located at least 19.7 inches from the nearest wall to ensure proper air conditioning.
- Medium Phillips screwdriver; - Tape measure or ruler; - Knife or scissors; - Saw (optional, to shorten window adaptor for narrow windows) Your Window Installation Kit fits windows 26.5 – 48" and can be shortened for smaller windows. Step One: Preparing the exhaust hose assembly. Press the exhaust hose into the window slider adaptor and the unit adaptor. Each adaptor will snap into the exhaust hose automatically with plastic clips.
Foam seal B (Short adhesive foam seal for right and left sides) Window slider B (if required) Window slider A Foam seal A (Long adhesive foam seal for top and bottom sides) Insert the window slider assembly on the bottom sash channel. Use care when installing the window slider assembly, which will now fit very tightly in the opening. Close the sash tightly against the top of the window slider assembly.
In order to ensure the optimal performance of our products, the design specifications of the unit and remote control are subject to change without prior notice.
MODE button Selects the desired operating mode. Each time you press the button, a mode is selected in a sequence that goes from COOL, FAN, and DRY. The mode light illuminates and indicates the selected mode. Up (+) and Down (-) buttons Used to adjust (increasing/decreasing) temperature settings in 1°C/1°F increments in a range of 17°C/62°F to 30°C/86°F. NOTE: The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius.
and read P1 on the LED display (it will stay like this until the unit is drained). If this happens, you should drain the water from the lower drain (located at the bottom of the unit). Note: When one of the above malfunctions occurs, turn off the unit and check for any obstructions. Restart the Unit. If the malfunction persists, turn off the unit and unplug the power cord. Contact the manufacturer or its service agents or a similarly qualified person for service.
SLEEP/ECO operation - This feature can be activated from the remote control ONLY. Activating SLEEP feature will increase the selected temperature by 1°C/1°F after 30 minutes. The temperature will again increase (cooling) by another 1°C/1°F after an additional 30 minutes. This new temperature will be maintained for 7 hours before returning to the originally selected temperature. This ends the Sleep/Eco mode and the unit will continue to operate as originally programmed.
down the grille Air filter (take out) Be sure to store the unit in a cool, dark place. Exposure to direct sunlight or extreme heat can shorten the lifespan of the unit.
Troubleshooting Tips Before calling for service, review this list. It may save you time and expense. This list includes common problems that may not be the result of defective workmanship or materials in this appliance.
