Safety Precaution Parts Description . Control e 6 s s m s sensationalism 43 Installation . 1" Maintenance . . 4B Troubleshooting ...t 17 Note: All the illustrations In this manual are for explanation purpose only. Your alr conditioner may be slightly different. The actual shape shall prevail. They are subject to change without notice for future Improvement. To:save the cost of a: service call, please try the suggestions below o see if you'can: solve your problem without outside help.
Before the cleaning of the alr conditioner, It must be shut down and the electricity must be cut off for mots than 5 minutes, otherwise there might be the risk of electric shocks. Do not use gasoline, benzene, thinner or any other chemicals, or any liquid insecticide on the air conditioner, as these substances may cause flaking off of the paint, cracking or deformation of plastic parts .
® An earth leakage breaker with rated capacity must be installed to avoid possible electric shocks. ® Don’ t install air conditioner in a place where there is flammable gas or liquid. @8 If the power supply cord is damaged, it must be replaced by the manufacture or its service agent or a similar qualified person. ® The specification of the fuse are printed on the circuit board, such as: AC 250V/5A, etc. ® Don't put hands or any objects into the air inlets or outlets. @ Don’ t touch the swinging wind vanes.
1. Prepare a hole In the wall. | . Install the wall exhaust oy pompano o adore adapter onto the wall by when not in use. using 4 expansion screw sleeve and type C screws, be sure to fix thoroughly. 2. Connect the exhaust duct to wall exhaust & WARNING Failure to follow the below precaution could result in electrical shock, fire or personal injury. 1.The plug must be plugged into an outlet that is properly installed and grounded. 2. Do not use an extension cord or plug adapter with this unit.
WERE Warning Meaning of crossed out wheeled dustbin: Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact you local government for information regarding the collection systems available.
2. Connect the exhaust duct to the Air outset connector an back of the unit. Slide-in the adapter A downwards until It Is locked In place. (Fig.C) &= Fig.C install the Window Slider Kit Horizontal 2.Attach the window slider kit to the window sash. Adjust the length of the Window Slider Kit: Loose the screw A to adjust the length of the Window Slider Kit, then tight the screw when the length Is suitable. Note: the length of the Window Slider Kit is 67.5¢m to 120cm.
There are four kinds of control panel, Fig A, Fig B, Fig © and Fig D, the ACLU! shape shall prevail. TEMP. indicator *C BEY L. ate ol dy fn het oF am M omd low » ® ® swing timer sleep mode Y A SGML on-off Guide of customer @Thea customer should have a squalled power supply coincident with that printed on the tag of the alr conditioner. ®Must use dedicated circuit and efficient grounding outlet matching with the plug of the air conditioner.
a Parts name natl Adapter A, Exhaust duct, Adapter B{flat mouth) , 1st Window Slider Kit forename Type A Screws(#) 2pc [ Type B Screws(#) ;gg h Security bracket(#) 1pe r Type Foam 2pe / Type B foam 1pc @ @ Adapter B(round , 1st Wall exhaust Adapter) sef Drain hose 1pc Remote controller and Battery pe Expansion screw 4pc Type C Screws(#) 4pc NOTE: Optional parts ( # ), some models without. NOTE: All the illustrations in this manual are for explanation purpose only.
7. timer/© / button a. Press the "timer” button, the timer indicator light illuminates. b. Press v button to select the desired time. c. After setting time 5 seconds without other operation, the timing function will be initiated automatically. If you press the timer button, there are no operation within § seconds or setting ime is 0, the timing function will be canceled automatically. d.