Installation Guide

ManualsBrandsKeystone ManualsHeating, Ventilation, and Air Conditioning6,000 BTU 115-Volt Window-Mounted Air Conditioner with LCD Remote Control

INSTALLATION INSTRUCTIONS

Read these instructions completely

and carefully.

IMPORTANT- Save these

instructions for local inspector s use.

IMPORTANT- Observe all

governing codes and ordianaces.

Note to Consumer- Keep these

instructions for futrue reference.

Note to Installer- Be sure to leave these

instructions with the Consumer.

Completion time- Approximately 1 hour.

Skill level- Installatio of this appliance

requires basic mechanical skills.

We recommend that two people install

this product.

Proper installation is the responsibility

of the installer.

Product failure due to improper installation

is not covered under the Warranty.

You MUST use all supplied parts and use

proper installation procedures as described

in these instructions when installing this air

conditioner.

BEFORE YOU BEGIN

Do not, under any circumstances, cut or

remove the third (ground) prong from the

power cord.

CAUTION

Do not change the plug on the power cord

of the air conditioner.

Aluminum house wiring may present special

problems- consult a qualified electircian.

When handling unit, be careful to avoid cuts from

sharp metal edges and aluminum fins on front and

rear coils.

TOOLS YOU WILL NEED

Screwdriver

Level

TOOLS YOU MAY USE

Screwdriver

Pencil

Ruler or tape measure

Scissors or knife

Save Carton and these Installation Instructions

for future reference. The carton is the best way

to store unit during winter, or when not in use.

NOTE:

Your air conditioner is designed to install in

standard double hung windows with opening

widths of 23 to 36 inches(584mm to 914mm) .

WINDOW REQUIREMENTS

Model

6000~8000Btu/h

10000~12000Btu/h

14 (356mm) 15-1/2 (394mm)

Table 1

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CAUTION BEFORE YOU BEGIN Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Read these instructions completely and carefully. IMPORTANT- Save these instructions for local inspector s use. IMPORTANT- Observe all governing codes and ordianaces. Note to Installer- Be sure to leave these instructions with the Consumer. Note to Consumer- Keep these instructions for futrue reference.
PAGE 2
INSTALLATION INSTRUCTIONS 1 C: Align the hole in the top rail with those in the top of the unit as shown in Fig.B PREPARE THE WINDOW Lower sash must open sufficiently to allow a clear vertical opening of 13 inches (330mm). Side louvers and the rear of the AC must have clear air space to allow enough airflow through the condenser, for heat removal. The rear of the unit must be outdoors, not inside a building or garage. Fig.
PAGE 3
INSTALLATION INSTRUCTIONS B. Slide the free end "Ⅰ" section of the panel directly into the cabinet as shown in Fig. 2. Slide the panel down. Be sure to leave enough space to slip the top and bottom of the frame into the rails on the cabinet. SECURE THE ACCORDION PANE LS A.Keep a firm grip on the air conditioner, carefully place the unit into the window opening so the bottom of the air conditioner frame is against the window sill (Fig.5). Carefully close the window behind the top rail of the unit.
PAGE 4
INSTALLATION INSTRUCTIONS B.Drive 3/4" (19mm) or 1/2" (12.7mm) locking screws through frame holes into window sash (Fig.8). Fig.8 C.To secure lower sash in place, attach right angle sash lock with 3/4" (19mm) or 1 /2" (12.7mm) screw as shown(Fig.9). 1 1 2 2 3 4 5 3 6 7 4 8 9 10 5 11 12 6 13 14 15 16 17 Measure the inner width of the side curtain Fig.11 Fig.9 D.Cut Window sash seal foam and insert it in the space between the upper and lower sashes (Fig.10). FOAM SEAL or Fig.
PAGE 5
INSTALLATION INSTRUCTIONS 7 INSTALL WEATHER STRIPPING (only be applicable to Energy star models ) If AC is Blocked by Storm Window Add wood as shown in Fig.15, or remove storm window before air conditioner is installed. In order to minimize air leaks between the room air conditoner and the window opening, trim the weather sttipping with a proper length, peel off the protective backing and plug any gaps if needed (Fig.14).