5" Terna LED TM 300230 A Kichler Decor ceiling fan ® ™ Includes our new CoolTouchTM Control System Looks permanent, but goes wherever you go! U.S. Patent Pending Kichler® Lighting 7711 East Pleasant Valley Road P.O. Box 318010 Cleveland, Ohio 44131-8010 Instruction Manual Customer Service 866.558.
1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control. Use only the control provided with the fan. 4.
15" Terna LED TM 2 2. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver 11 mm wrench Step ladder Wire cutters 3. PACKAGE CONTENTS Unpack your fan and check the contents . You should have the following items: A. B. C. D. E. F. G. H. I. J. K. L. M.
3 4. MOUNTING OPTIONS If there isn't an existing ETL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Outlet box Fig. 1 Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 50 lbs). Do not use plastic outlet boxes.
15" Terna LED TM 5. ASSEMBLE YOUR CEILING FAN Step 1. Remove the hanger ball from downrod assembly by loosening set screws , removing the cross pin, and sliding ball off the rod. ( Fig. 5) 4 Hanger Ball Set Screw Cross Pin Downrod Step 2. Remove the fan motor and housing assembly from the protective plastic bag and take the lower styrofoam packing pad out of the carton. Place the styrofoam pad on the floor.
5 Blade Step 2. Carefully turn over the motor body with the bottom of motor facing up. Attach the blade arm to the flywheel and let the tab on the blade leg pass through the hole on the blade arm, as shown (Fig. 9). Make sure yellow tab is visible through hole and metal bracket. Align the two mounting holes on both side of blade arm with the holes on the flywheel and tighten them with truss head blade screws provided. Finally, tighten the two flat head blade screws in the ring.
15" Terna LED TM 8 . INSTALLATION OF SAFETY SUPPORT (required for Canadian installation ONLY) A safety support cable is provided to help prevent the ceiling fan from failing, please install it as follows. Support Brace Flat Washer Wood Screw Spring Washer Ceiling Outlet Box Step 1. Drive a wood screw and washers into the side of the brace that holds the outlet box. Leave 3mm (1/8") of space between the support brace and the washer. (Fig. 13) Step2.
7 TM Battery Compartment ON ECE ON ECE Code Switch Fig. 15 Mounting Bracket NOTE: The CoolTouch Control System is equipped with 16 code combinations to prevent possible interference from or to other remote units. The frequency switches on your receiver and transmitter have been preset at the factory. Remove the transmitter battery cover and make sure the switches are set to the same position. This must be done so that your fan will communicate properly.
15" Terna LED TM 10 . FINISHING THE INSTALLATION Step 1. Remove one of the two shoulder screws in the mounting bracket. Loosen the second shoulder screw without fully removing it. (Fig. 18) Mounting Bracket Shoulder Screw Fig. 18 Step 2. Assemble canopy by rotating key slot in canopy over shoulder screw in mounting bracket. Tighten shoulder screw. Fully assemble and tighten second shoulder screw that was previously removed. (Fig. 19) Shoulder Screw Fig. 19 Step 3.
9 12. INSTALLING THE LED Assembly NOTE: Before continuing installation, confirm that the power is still turned off at the main circuit breaker or by removing the correct fuse. Turning the power off using a wall switch is not sufficient to prevent electrical stock. Adapter Plate LED Assembly Fig. 22 Step 1. Remove 1 of the 3 screws from the adapter plate and loosen the other 2 screws (do not remove). (Fig. 22) Step 2.
15" Terna LED TM 14. INSTALLING THE COOLTOUCH CONTROL SYSTEM WALL PLATE 10 TM Outlet Box All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. Switch Wall Plate TM Select a location to install your CoolTouch Control System Transmitter. You can replace an existing wall switch, or install the transmitter on ANY flat surface.
11 16. CONTROL SYSTEM SET-UP NOTE: Make sure the power is completely disconnected before you begin this procedure. Read all of these steps before preceeding. Each step must be followed exactly to properly program the control system. ECE ON 2032 CHLER + 2032 R CEILING FANS THE AIR OF DISTINCTION TM Step 1. Install 2,3 volt # 2032 battery included with the CoolTouchTM Control system and make sure they are seated correctly in each recess with the Positive + Sign facing up. Replace the battery cover .
15" Terna LED TM 17. OPERATING INSTRUCTIONS: Speed Buttons Restore power to ceiling fan and test for proper operation. Figure 30: 1. Buttons , , : These three buttons are used to set the fan speed as follows: Forward/Reverse Button = Low Speed = Medium Speed = High Speed Fig. 30 Figure 31: 1. The " " buttons: This button turns the fan motor off and is also used in the program procedure. 2. The " " and " " button: These two buttons turn the light ON or OFF and also controls the brightness setting.
13 18. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check all electrical connections to insure proper contact. CAUTION: Make sure the main power is OFF when checking any electrical connection. 3. Make sure the transmitter batteries are installed properly. Positive (+) side facing out. 4. Insure the batteries have a good charge. Fan sounds noisy. 1. Make sure all motor housing screws are snug. 2.