ITEM #0616008 5-LIGHT CHANDELIER Kichler® is a registered trademark of The L.D. Kichler Co. All Rights Reserved. MODEL #34686 Français p. 11 Español p. 21 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-554-6504, 8 a.m. - 4:30 p.m, EST, Monday - Friday.
PACKAGE CONTENTS B C D H A I K L N F P J O M G E PART A B C D E F G H I J K L M N O P DESCRIPTION Canopy Mounting Bracket Threaded Nipple Hex Nut (preassembled to Threaded Nipple (C)) Socket (preassembled to Arm (O)) Coupling Shade Screw Collar Ring (preassembled to Threaded Nipple (C)) Screw Collar Loop (preassembled to Threaded Nipple (C)) Spacer Chain Fixture Loop Socket Ring (preassembled to socket (E)) Threaded Pipe Arm 60-Watt Edison Bulb 2 QUANTITY 1 1 1 3 5 1 5 1 1 5 1 1 5 1 5 5
HARDWARE CONTENTS AA Wire Connector Qty: 3 BB Short Machine Screw Qty: 2 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. • • • • • WARNING IMPORTANT: NEVER attempt any work without shutting off the electricity. Place the main power switch in the “OFF” position and unscrew the fuse(s), or switch “OFF” the circuit breaker switch(es), that control the power to the fixture or room you are working in.
ASSEMBLY INSTRUCTIONS 1. Screw fixture loop (L) onto threaded pipe (N) before screwing threaded pipe onto coupling (F). 1 L N F 2. Position threaded nipple (C) in mounting bracket (B) so that, when mounted: • • The threaded nipple (C) will protrude a minimum of ¼ inch beyond the raised center portion of the bracket (B). The threaded nipple (C) height should be positioned so that ½ the exterior threads of the screw collar loop (I) will extend past the canopy (A), when it is mounted. 3.
ASSEMBLY INSTRUCTIONS 4. Connect mounting bracket (B) to the outlet box with short machine screws (BB). 4 Outlet Box Hardware Used BB Short Machine Screw x2 B C BB 5. Using the open chain links on chain (K), attach one end to screw collar loop (I) and the other end to fixture loop (L). Weave the fixture electrical and ground wires through every other chain link and pass through threaded nipple (C) into outlet box. Lower the screw collar ring (H) and canopy (A) over the chain (K).
ASSEMBLY INSTRUCTIONS 6. Wire connection guide: Ground wire: • For installation in the United States: Wrap ground wire from outlet box around ground screw on mounting bracket (B) no less than 2 in. from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector (AA). • For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around ground screw on mounting bracket (B). Tighten ground screw.
ASSEMBLY INSTRUCTIONS 8. Lower shade (G) over socket (E). Next screw spacer (J) then socket ring (M) onto socket (E). 8 Wrench Repeat for remaining sockets (E). M J G E 9. Insert 60-watt max. Edison bulb (P) into socket (E). 9 P Repeat for remaining sockets (E).
CARE AND MAINTENANCE • Always be certain that electric current is turned off before cleaning this item. • Use a soft, moist cloth with mild non-abrasive soap to clean fixture. Never use glass cleaner on fixture, as it will damage the metal finish. • All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher. TROUBLESHOOTING PROBLEM POSSIBLE CAUSE 1.CORRECTIVE Check wiring. ACTION Fixture does not light. 1.
WARRANTY (continued) This warranty does not apply to any products that have been subjected to misuse, mishandling, misapplication, connected to voltage at more than 5% above standard North American voltage, unusual use (including but not limited to use in an environment where the annual average ambient operating temperature is below 27 or above 95 degrees Fahrenheit), neglect (including but not limited to improper maintenance), accident, acts of god such as high winds, improper installation or care, failure
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-800-554-6504, 8 a.m. - 4:30 p.m., EST, Monday - Friday.
ARTICLE #0616008 LUSTRE À 5 LUMIÈRES Kichler® est une marque déposée de The L.D. Kichler Co. Tous droits réservés. MODÈLE #34686 JOIGNEZ VOTRE REÇU ICI Numéro de série Date d’achat Des questions, des problèmes, des pièces manquantes? Avant de retourner le produit à votre détaillant, appelez notre service à la clientèle au 1-800-554-6504, entre 8 h et 16 h 30 (HNE) du lundi au vendredi.
CONTENU DE L’EMBALLAGE B C D H A I K L N F P J O M G E PIÈCE A B C D E F G H I J K L M N O P DESCRIPTION Pavillon Support de fixation Raccord fileté Écrou hexagonal (préassemblé au raccord fileté (C)) Douille (préassemblée au bras (O)) Raccord Abat-jour Bague de serrage vissée (préassemblée au raccord fileté (C)) Anneau de suspension du pavillon (préassemblé au raccord fileté (C)) Entretoise Chaîne Anneau de suspension du luminaire Bague de douille (préassemblée à la douille (E)) Tube fileté Br
QUINCAILLERIE INCLUSE AA BB Capuchon de connexion Vis à Qté : 3 métaux courte Qté : 2 CONSIGNES DE SÉCURITÉ Veuillez vous assurer de lire et de comprendre l’intégralité du présent guide avant d’assembler, d’utiliser ou d’installer ce produit. AVERTISSEMENT • IMPORTANT : Coupez l’électricité avant TOUTE manipulation. • Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »).
INSTRUCTIONS POUR L'ASSEMBLAGE 1. Vissez l'anneau de suspension du luminaire (L) sur le tube fileté (N) avant de visser le tube fileté sur le raccord (F). 1 L N F 2. Positionnez le raccord fileté (C) dans le support de fixation (B) de sorte que, une fois le montage effectué : • • • • Vissez le 1er écrou hexagonal (D) sur le raccord fileté (C) et serrez-le contre la partie saillante du support (B).
INSTRUCTIONS POUR L'ASSEMBLAGE 4. Fixez le support de fixation (B) à la boîte de sortie à l'aide des vis à métaux courtes (BB). 4 Boîte de sortie Quincaillerie utilisée BB Vis à métaux courte x2 B C BB 5. À l'aide des anneaux ouverts de la chaîne (K), attachez une extrémité à l'anneau de suspension du pavillon (I) et l'autre extrémité à l'anneau de suspension du luminaire (L).
INSTRUCTIONS POUR L'ASSEMBLAGE 6. Guide de raccordement électrique 6 Fil de mise à la terre : • Pour une installation aux États-Unis : enroulez le fil de mise à la terre provenant de la boîte de sortie autour de la vis de mise à la terre située sur le support de fixation (B), à au moins 5,08 cm de l’extrémité du fil. Serrez la vis de mise à la terre.
INSTRUCTIONS POUR L'ASSEMBLAGE 8. Abaissez l'abat-jour (G) par-dessus la douille (E). Vissez l'entretoise (J) puis la bague de la douille (M) sur la douille (E). 8 Wrench Répétez l'opération pour les douilles restantes (E). M J G E 9. Insérez une ampoule Edison de 60 watts max. (P) dans la douille (E). 9 P Répétez l'opération pour les douilles restantes (E).
ENTRETIEN • Vérifiez toujours que le courant est coupé avant de nettoyer le luminaire. • Utilisez un linge doux et humide ainsi qu’un savon non abrasif. N’utilisez jamais de nettoyants pour vitres; vous risqueriez d’endommager le fini métallique du luminaire. • Les abat-jour en verre peuvent être nettoyés dans un évier couvert de serviettes, à l’aide d’eau tiède et de savon doux. Ne nettoyez pas les abat-jour dans un lave-vaisselle. DÉPANNAGE PROBLÈME Le luminaire ne s’allume pas. CAUSE POSSIBLE 1.
GARANTIE (suite) Cette garantie ne s'applique pas aux produits qui ont été soumis à un usage abusif, une manipulation inadéquate, un usage impropre, qui ont été connectés à un voltage de plus de 5 % supérieur au voltage nord américain, qui ont subi un usage inhabituel (y compris mais sans s'y limiter un usage dans un environnement où la température ambiante moyenne annuelle est inférieure à 27 °F [-2,8 °C] ou supérieure à 95 °F [35 °C]), la négligence (y compris mais sans s'y limiter un mauvais entretien),
LISTE DES PIÈCES DE RECHANGE Pour obtenir des pièces de rechange, appelez notre service à la clientèle au 1-800-554-6504, entre 8 h et 16 h 30 (HNE), du lundi au vendredi.
ARTÍCULO #0616008 Kichler® es una marca registrada de The L.D. Kichler Co. Todos los derechos reservados. ARAÑA DE 5 LUCES MODELO #34686 ADJUNTE SU RECIBO AQUÍ Número de serie Fecha de compra ¿Preguntas, problemas, piezas faltantes? Antes de devolverlo a la tienda, llame a nuestro departamento de servicio al cliente al 1-800-554-6504, de 8:00 a.m. a 4:30 p.m. hora del Este (EST), de lunes a viernes.
CONTENIDO DEL PAQUETE B C D H A I K L N F P J O M G E PIEZA A B C D E F G H I J K L M N O P DESCRIPCIÓN Cubierta Soporte de montaje Manguito roscado Tuerca hexagonal [preinstalada en el Manguito roscado (C)] Portalámparas [preinstalado en el Brazo (O)] Acoplamiento Pantalla Anillo de cuello roscado [preinstalado en el Manguito roscado (C)] Bucle de cuello roscado [preinstalado en el Manguito roscado (C)] Espaciador Cadena Bucle de colgar de la lámpara Aro para portalámparas [preinstalado en el
ADITAMENTOS AA Conector de cables Cant.: 3 BB Tornillo corto para metales Cant.: 2 INFORMACIÓN DE SEGURIDAD Lea y comprenda completamente este manual antes de intentar ensamblar, usar o instalar el producto. • • • • • ADVERTENCIA IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico. Coloque el interruptor de alimentación principal en la posición “OFF” (APAGADO). Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
INSTRUCCIONES DE ENSAMBLAJE 1. Atornille el bucle de colgar la lámpara (L) al tubo roscado (N) antes de atornillar el tubo roscado al acoplamiento (F). 1 L N F 2. Coloque el manguito roscado (C) en el soporte de montaje (B), de manera que al quedar montado: • • • • Atornille la primera tuerca hexagonal (D) al manguito roscado (C) y apriétela contra la porción que sobresale del soporte (B).
INSTRUCCIONES DE ENSAMBLAJE 4. Conecte el soporte de montaje (B) a la caja eléctrica con tornillos cortos para metal (BB). 4 Caja de salida Aditamentos utilizados BB Tornillo corto para metales x2 B C BB 5. Usando los eslabones abiertos en la cadena (K), fije un extremo al bucle de cuello roscado (I) y el otro extremo al bucle de colgar la lámpara (L).
INSTRUCCIONES DE ENSAMBLAJE 6. Guía de conexión de cables: 6 Cable a tierra: • Para la instalación en los Estados Unidos: Enrolle el cable a tierra de la caja eléctrica alrededor del tornillo a tierra en la abrazadera de montaje (B), a no menos de 5 cm (2") del extremo del cable. Apriete el tornillo a tierra. Si la lámpara viene con un cable a tierra, conéctelo al cable a tierra de la caja eléctrica con un conector de cables (AA).
INSTRUCCIONES DE ENSAMBLAJE 8. Baje la pantalla (G) sobre el portalámparas (E). Luego atornille el espaciador (J) y después el aro para portalámparas (M) al portalámparas (E). 8 Wrench Repita para los portalámparas restantes (E). M J G E 9. Inserte un foco Edison de máximo 60 W (P) en el portalámparas (E). 9 P Repita para los portalámparas restantes (E).
CUIDADO Y MANTENIMIENTO • Siempre asegúrese de que la corriente eléctrica esté desconectada antes de limpiar. • Utilice un paño húmedo suave y jabón suave no abrasivo para limpiar la lámpara. Nunca utilice un limpiador para vidrio en la lámpara, porque éste dañará el acabado metálico. • Las pantallas de vidrio se pueden lavar dentro de un lavabo recubierto con toallas usando agua tibia y jabón suave. No lave las pantallas en un lavaplatos automático.
GARANTÍA (continuación) Esta garantía no aplica a ningún producto que haya sido objeto de uso indebido, manipulación indebida, aplicación indebida, conectado a voltaje superior al 5 % del voltaje norteamericano estándar, uso inusual (incluyendo sin limitación el uso en un ambiente donde la temperatura promedio anual de operación sea inferior a 27 oF [-2.
LISTA DE PIEZAS DE REPUESTO Para repuestos, llame a nuestro departamento de servicio al cliente al 1-800-554-6504, de 8:00 a.m. a 4:30 p.m. hora del Este (EST), de lunes a viernes.