ITEM #0616386 3-LIGHT PENDANT Kichler® is a registered trademark of The L.D. Kichler Co. All Rights Reserved. MODEL #34734 Français p. 10 Español p. 19 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-554-6504, 8 a.m. - 4:30 p.m, EST, Monday - Friday.
PACKAGE CONTENTS B A D C H I K L J N G E F M PART A B C D E F G DESCRIPTION Canopy Mounting Bracket Threaded Nipple Hex Nut Socket Coupling Threaded Pipe QTY 1 1 1 3 3 1 1 PART H I J K L M N 2 DESCRIPTION Screw Collar Ring Screw Collar Loop Spider Chain Fixture Loop Arm Shade QTY 1 1 1 1 1 3 1
HARDWARE CONTENTS AA Wire Connector Qty: 3 BB Short Machine Screw Qty: 2 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. • • • • • WARNING IMPORTANT: NEVER attempt any work without shutting off the electricity. Place the main power switch in the “OFF” position and unscrew the fuse(s), or switch “OFF” the circuit breaker switch(es), that control the power to the fixture or room you are working in.
ASSEMBLY INSTRUCTIONS 1. Screw threaded pipe (G) onto coupling (F). 1 G F 2. Pass threaded pipe (G) through spider (J) on shade (N) and secure using fixture loop (L). 2 L J G N 3. Position threaded nipple (C) in mounting bracket (B) so that, when mounted: • • The threaded nipple (C) will protrude a minimum of ¼ inch beyond the raised center portion of the bracket (B).
ASSEMBLY INSTRUCTIONS 4. Once the proper position of the threaded nipple (C) and bracket (B) has been determined, secure with 3 hex nuts (D) as follows: • • • Screw 1st hex nut (D) onto the threaded nipple (C) and tighten against the raised portion of the bracket (B). Screw 2nd hex nut (D) onto the threaded nipple (C) and tighten against the flat portion of the mounting bracket (B). Screw the third hex nut (D) onto threaded nipple (C) and tighten against the screw collar loop (I). 5.
ASSEMBLY INSTRUCTIONS 6. Using the open chain links on chain (K), attach one end to screw collar loop (I) and the other end to fixture loop (L). Weave the fixture electrical and ground wires through every other chain link and pass through threaded nipple (C) into outlet box. Lower the screw collar ring (H) and canopy (A) over the chain (K). 6 Outlet Box I C K A H L 7.
ASSEMBLY INSTRUCTIONS 8. Pass canopy (A) over the screw collar loop (I). Attach screw collar ring (H) to screw collar loop (I) to secure canopy (A). 8 I A H 9. Insert 60-watt candelabra-base bulb (not included) into socket (E). 9 Repeat for remaining sockets. E CARE AND MAINTENANCE • Always be certain that electric current is turned off before cleaning this item. • Use a soft, moist cloth with mild non-abrasive soap to clean fixture.
WARRANTY Kichler Lighting warrants that its products will be free from defects in material and workmanship for one (1) year from the date of purchase by the Original Purchaser. To replace a product that has a warranted defect, the Original Purchaser shall return any allegedly defective parts or products to the authorized Kichler distributor that the product was purchased from with PROOF OF PURCHASE, Original Purchaser’s name and return address and a description of the claimed product defect.
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-800-554-6504, 8 a.m. - 4:30 p.m., EST, Monday - Friday.
ARTICLE #0616386 LUMINAIRE SUSPENDU À 3 LUMIÈRES Kichler® est une marque déposée de The L.D. Kichler Co. Tous droits réservés. MODÈLE #34734 JOIGNEZ VOTRE REÇU ICI Numéro de série Date d’achat Des questions, des problèmes, des pièces manquantes? Avant de retourner le produit à votre détaillant, appelez notre service à la clientèle au 1-800-554-6504, entre 8 h et 16 h 30 (HNE) du lundi au vendredi.
CONTENU DE L’EMBALLAGE B A D C H I K L J N G E F M PIÈCE A B C D E F G DESCRIPTION Pavillon Support de fixation Raccord fileté Écrou hexagonal Douille Raccord Tube fileté QTÈ 1 1 1 3 3 1 1 PIÈCE DESCRIPTION QTÈ 1 H Bague de l'anneau du pavillon 1 Anneau de suspension du pavillon I 1 Fixation lyre J 1 K Chaîne L Anneau de suspension du luminaire 1 3 M Bras N 1 Abat-jour 11
QUINCAILLERIE INCLUSE AA BB Capuchon de connexion Vis à Qté : 3 métaux courte Qté : 2 CONSIGNES DE SÉCURITÉ Veuillez vous assurer de lire et de comprendre l’intégralité du présent guide avant d’assembler, d’utiliser ou d’installer ce produit. AVERTISSEMENT • IMPORTANT : Coupez l’électricité avant TOUTE manipulation. • Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »).
INSTRUCTIONS POUR L'ASSEMBLAGE 1. Vissez le tube fileté (G) dans le raccord (F). 1 G F 2. Faites passer le tube fileté (G) à travers la fixation lyre (J) de l’abat-jour (N) et fixez-le à l'aide de l’anneau de suspension du luminaire (L). 2 L J G N 3.
INSTRUCTIONS POUR L'ASSEMBLAGE 4. Lorsque les positions correctes du raccord fileté (C) et du support (B) ont été déterminées, fixez à l'aide de 3 écrous hexagonaux (D), comme suit : • • • Vissez le 1er écrou hexagonal (D) sur le raccord fileté (C) et serrez-le contre la partie saillante du support (B). Vissez le 2e écrou hexagonal (D) sur le raccord fileté (C) et serrez-le contre la partie plate du support de fixation (B).
INSTRUCTIONS POUR L'ASSEMBLAGE 6. À l'aide des anneaux ouverts de la chaîne (K), attachez une extrémité à l'anneau de suspension du pavillon (I) et l'autre extrémité à l'anneau de suspension du luminaire (L). Tressez le fil de terre et les fils électriques du luminaire à travers un maillon sur deux de la chaîne et faites-les passer à travers le raccord fileté (C) puis dans la boîte de sortie. Abaissez la bague de l’anneau du pavillon (H) et le pavillon (A) le long de la chaîne (K).
INSTRUCTIONS POUR L'ASSEMBLAGE 8. Faites passer le pavillon (A) sur l'anneau de suspension du pavillon (I). Attachez la bague de l’anneau du pavillon (H) à l'anneau de suspension du pavillon (I) pour fixer le pavillon (A). 8 I A H 9. Insérez une ampoule à culot candélabre de 60 watts max. (non fournie) dans la douille (E). 9 Répétez l'opération pour les douilles restantes. E ENTRETIEN • Vérifiez toujours que le courant est coupé avant de nettoyer le luminaire.
GARANTIE Kichler Lighting garantit que ses produits seront libres de tout vice de fabrication ou défaut matériel pendant un (1) an à compter de la date d'achat par l'acheteur initial.
LISTE DES PIÈCES DE RECHANGE Pour obtenir des pièces de rechange, appelez notre service à la clientèle au 1-800-554-6504, entre 8 h et 16 h 30 (HNE), du lundi au vendredi.
ARTÍCULO #0616386 Kichler® es una marca registrada de The L.D. Kichler Co. Todos los derechos reservados. LÁMPARA COLGANTE DE 3 LUCES MODELO #34734 ADJUNTE SU RECIBO AQUÍ Número de serie Fecha de compra ¿Preguntas, problemas, piezas faltantes? Antes de devolverlo a la tienda, llame a nuestro departamento de servicio al cliente al 1-800-554-6504, de 8:00 a.m. a 4:30 p.m. hora del Este (EST), de lunes a viernes.
CONTENIDO DEL PAQUETE B A D C H I K L J N G E F M PIEZA A B C D E F G DESCRIPTIÓN Cubierta Soporte de montaje Manguito roscado Tuerca hexagonal Portalámparas Acoplamiento Tubo roscado CANT 1 1 1 3 3 1 1 PIEZA H I J K L M N 20 DESCRIPTIÓN Anillo de cuello roscado Bucle de cuello roscado Araña Cadena Bucle para colgar la lámpara Brazo Pantalla CANT 1 1 1 1 1 3 1
ADITAMENTOS AA Conector de cables Cant.: 3 BB Tornillo corto para metales Cant.: 2 INFORMACIÓN DE SEGURIDAD Lea y comprenda completamente este manual antes de intentar ensamblar, usar o instalar el producto. • • • • • ADVERTENCIA IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico. Coloque el interruptor de alimentación principal en la posición “OFF” (APAGADO). Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
INSTRUCCIONES DE ENSAMBLAJE 1. Atornille el tubo roscado (G) al acoplamiento (F). 1 G F 2. Pase el tubo roscado (G) por la araña (J) en la pantalla (N) y asegúrelo usando el bucle para colgar la lámpara (L). 2 L J G N 3. Coloque el manguito roscado (C) en el soporte de montaje (B), de manera que al quedar montado: • • El manguito roscado (C) sobresalga un mínimo de 6.35 mm (1/4 pulgada) encima de la porción central elevada del soporte (B).
INSTRUCCIONES DE ENSAMBLAJE 4. Una vez se haya determinado la posición adecuada del manguito roscado (C) y del soporte (B), fíjelos con 3 tuercas hexagonales (D) como se indica a continuación: • • • 4 ¼ Pulgada B C Atornille la primera tuerca hexagonal (D) al manguito roscado (C) y apriétela contra la porción que sobresale del soporte (B). Atornille la segunda tuerca hexagonal (D) al manguito roscado (C) y apriétela contra la porción plana del soporte de montaje (B).
INSTRUCCIONES DE ENSAMBLAJE 6. Usando los eslabones abiertos en la cadena (K), fije un extremo al bucle de cuello roscado (I) y el otro extremo al bucle de la lámpara (L). Entrelace los cables eléctricos y a tierra de la lámpara por los eslabones, uno sí y otro no, y páselos por el manguito roscado (C) a la caja eléctrica. Deslice el anillo de cuello roscado (H) y la cubierta (A) por la cadena (K). 6 I Caja de C salida K A H L 7 7.
INSTRUCCIONES DE ENSAMBLAJE 8. Pase la cubierta (A) sobre el bucle de cuello roscado (I). Fije el anillo de cuello roscado (H) al bucle de cuello roscado (I) para fijar la cubierta (A). 8 I A H 9. Inserte un foco de base para candelabro de máximo 60 W (no se incluye) en el portalámparas (E). 9 Repita para los portalámparas restantes. E CUIDADO Y MANTENIMIENTO • Siempre asegúrese de que la corriente eléctrica esté desconectada antes de limpiar.
GARANTÍA Kichler Lighting garantiza que sus productos estarán libres de defectos de materiales o mano de obra por un (1) año a partir de la fecha de compra por el Comprador Original.
LISTA DE PIEZAS DE REPUESTO Para repuestos, llame a nuestro departamento de servicio al cliente al 1-800-554-6504, de 8:00 a.m. a 4:30 p.m. hora del Este (EST), de lunes a viernes.