Installation Guide

1) Pass wire from fixture through stem and screw stem to top
of fixture. NOTE: Thread locking compound must be applied
to all stem threads as noted with symbol (3) to prevent
accidental rotation of fixture during cleaning, relamping, etc.
2) Pass fixture wire through remaining stems and screw stems
together.
3) Thread one small threaded pipe into end of each small loop.
4) On each side of fixture, pass fixture wire from last stem
through first loop. Thread each first loop onto end of each
last stem.
5) On each side of fixture, pass fixture wire through each small
loop on canopy and through hole in canopy.
6) Attach one chain link to small loop at end of each stem and
to each small oop on canopy.
7) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room that
you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
8) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
9) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
10) Attach safety cable to slot in mounting strap
11) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never connect
ground wire to black or white power supply wires.
12) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
13) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
14) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
15) Insert recommended bulb.
16) Slip one small rubber washer onto each thumbscrew.
17) Raise glass up to fixture. Pass hole in glass over bulb.
18) Align holes in side of glass with holes in ring on socket.
19) Carefully push end of thumbscrew into hole in glass and
thread thumbscrew into hole in side of ring on socket.
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 12/11/15 IS-43457-US
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
CANOPY
ESCUDETE
STEM
VÁSTAGO
LOOP
ANILLO
CHAIN LINK
ESLABÓN DE
CADENA
4
MOUNTING STRAP
PLANCHA PARA MONTAR
3
GLASS
VIDRIO
COUPLING
ACOPLAMIENTO
THUMBSCREW
TORNILLO DE
MARIPOSA
SMALL RUBBER WASHER
PEQUEÑA ARANDELA DE
CAUCHO
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
KNURL KNOB
PERILLA
ESTRADA
SAFETY CABLE
ACTIVACIÓN DE SEGURIDAD
3
4