Installation Sheet

IS-10798-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
REV 7-JUNE-2021
For warranty informaon please visit: kichler.com/warranty
1) Assemble mounng screws to backpan using hexnut.
2) At the center of the backpan are knockout slots. Remove
the set that matches your outlet box.
3) Posion the backplate over the outlet box. Secure the
backpan to the outlet box using mounng strap screws
provided (these are the shorter of the two screws)
4) Mark the locaon of the outer keyhole slots of the
backplate to the wall. Be sure to mark only the narrow
part of the keyhole slot. Remove the backplate from the
wall. Drill the holes using an appropriately sized drill bit.
Insert the provided anchors into the holes.
5) Grounding instrucons: (See Illus. A or B)
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided, put
ground wire from outlet box under cupped washer
and green ground screw and thread screw into hole
in mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps. Never connect
ground wire to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
6) Make wire connecons. Reference chart below for
correct connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord
(round & smooth)
*Parallel cord
(square & ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
7) Carefully push wire connecons back into outlet box
making sure all connecons remain secure.
8) Secure the backpan to the outlet box with the mounng
strap screws.
9) Anchor the backpan to the wall using the set of holes at
each end of xture using the provided wood screws and
plasc anchors.
10) Slip the holes of the faceplate over mounng screws and
backpan.
11) Secure faceplate to backpan using lockwashers and lock-
up knobs.
12) Carefully lower each diuser and rest onto the boom
tabs of the side brackets.
Fixture Diagram
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with the
Naonal Electrical Code (NEC) and all local code specicaons.
If you are not familiar with code requirements, installaon by a
cered electrician is recommended.
DIMMING:
This LED xture is compable with most standard incandescent
dimmers, LED dimmers, and electronic low voltage dimmers.
For opmal performance, an electronic low voltage dimmer should
be used.
See kichler.com/dimming for a list of compable dimmers.
CLEANING:
• Always be certain that electric current is turned o before
cleaning.
• Only a so damp cloth should be used. Harsh cleaning
products may damage the nish.
Installaon Instrucons
This device complies with part 15 of the FCC Rules. Operaon is subject to
the following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including
interference that may cause undesired operaon.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protecon against harmful
interference in a residenal installaon. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instrucons, may cause harmful interference to radio
communicaons. However, there is no guarantee that interference will
not occur in a parcular installaon. If this equipment does cause harmful
interference to radio or television recepon, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Informaon:
DIFFUSER
LED MODULE
OUTLET BOX
WIRE
CONNECTORS
MOUNTING PLATE
MOUNTING SCREW(S)
HEXNUT(S)
10798LED (USE FOR 10799LED & 10800LED)
FACE PLATE