Installation Sheet

Date Issued: 10/12/17 IS-11253LED-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starting and during the installation.
4) Grounding instructions: (See Illus. A or B).
 A) Onxtureswheremountingstrapisprovidedwithahole
andtworaiseddimples.Wrapgroundwirefromoutletbox
aroundgreengroundscrew,andthreadintohole.
 B) Onxtureswhereacuppedwasherisprovided.Attach
 groundwirefromoutletboxundercuppedwasherand
 greengroundscrew,andthreadintomountingstrap.
 Ifxtureisprovidedwithgroundwire.Connectxtureground
wiretooutletboxgroundwirewithwireconnector.(Notpro-
vided.)Afterfollowingtheabovesteps.Neverconnectground
wiretoblackorwhitepowersupplywires.
5) Makewireconnections.Referencechartbelowforcorrectcon-
nectionsandwireaccordingly.
6) Placextureuptomountingplate.Carefullypushwirecon-
nections[6]insidemountingplateandcanopymakingsureall
connectionsremainsecureandwiresdonotgetpinched.
7) InsertandtightenmountingscrewstosecureFixturetowall.
CLEANING DIFFUSER INSTRUCTIONS:
1) Removescrew[7]fromendcap[8].Slideendcapoutofxture
andsetaside.
2) Slidediffuser[9]outofxturetakingcarenottotouchLED
module[10].
3) Onlyadampclothshouldbeusedtocleandiffuser.Harsh
cleaningproductsmaydamagethenish.
4) Assembleinreverseorder.
WARNING:
Thisxtureisintendedforinstallationinaccordancewiththe
NationalElectricalCode(NEC)andalllocalcodespecications.
Ifyouarenotfamiliarwithcoderequirements,installationbya
certiedelectricianisrecommended.
CLEANING:
Alwaysbecertainthatelectriccurrentisturnedoffbeforecleaning.
Onlyadampclothshouldbeused.Harshcleaningproductsmay
damagethenish.
FCC INFORMATION:
Thisdevicecomplieswithpart15oftheFCCRules.Operationis
subjecttothefollowingtwoconditions:
(1) Thisdevicemaynotcauseharmfulinterference,and
(2) thisdevicemustacceptanyinterferencereceived,including
interferencethatmaycauseundesiredoperation.
Note:Thisequipmenthasbeentestedandfoundtocomplywiththe
limitsforaClassBdigitaldevice,pursuanttopart15oftheFCC
Rules.Theselimitsaredesignedtoprovide
reasonableprotectionagainstharmfulinterferenceinaresidential
installation.Thisequipmentgenerates,usesandcan
radiateradiofrequencyenergyand,ifnotinstalledandused
inaccordancewiththeinstructions,maycauseharmful
interferencetoradiocommunications.However,thereisno
guaranteethatinterferencewillnotoccurinaparticularinstallation.
Ifthisequipmentdoescauseharmfulinterference
toradioortelevisionreception,whichcanbedeterminedby
turningtheequipmentoffandon,theuserisencouragedto
trytocorrecttheinterferencebyoneormoreofthefollowingmea-
sures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfrom
thattowhichthereceiverisconnected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
INSTALLATION:
• Readandunderstandallinstructionsandillustrationscom-
pletelybeforeproceedingwithassemblyandinstallationof
xture.
• Ifyouhaveanydoubtsabouthowtoinstallthisxture,orifthe
xturefailstooperatecompletely,pleasecontactaqualied
electrician.
• Allpartsmustbeusedasindicatedintheinstructions.Donot
substituteanyparts,leavepartsout,oruseanypartsthatare
wornorbroken.Failuretoobeythisinstructioncouldinvalidate
theULlisting,C.S.A.certication,and/orETLlistingofthis
xture.
• Fixtureistobeconnectedtoasinglebranchcircuit.
• Mountingsurfaceshouldbeclean,dry,flatand1/4”largerthan
thexturehousingsurface.
INSTRUCTIONS:
1) Remove(4)MountingScrews[1].
2) Slidemountingplate[2]outofcanopy[3].
3) Attachthemountingplatetotheoutletbox[4]withsupplied
screws[5].
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
2
4
3
1
5
6
8
9
10
7
Connect Black or Red
Supply Wire to:
Connect White Supply Wire to:
Blac
kW
hite
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wire (SPT I & SPT II)
are used. The neutral wire is square shaped or
ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire