Installation Guide

INSTRUCTIONS PERTAINING TO A RISK OF FIRE,OR INJURY TO
PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.
1) Turn off / unplug and allow to cool before replacing lamp.
2) Lamp gets HOT quickly! Contact only switch / plug when turning on.
3) Do not touch hot lens or cowl.
4) Do not remain in light if skin feels warm. (Light is intense, it may cause
“sunburn”.)
5) Do not look directly at lighted lamp.
6) Keep lamp away from materials that may burn.
7) Useonlywithwattageandlampmarkedonxture.
8) Do not touch the inner glass envelope of the lamp at any time. Use a soft
cloth. Oil from skin may damage lamp.
9) Donotoperatethexturewithadamagedormissinglens.
SAFETY INSTRUCTIONS
READ THIS FIRST
KEEP THESE INSTRUCTIONS
This xture is intended for installation in accordance with the National
Electric Code (NEC) and Local code specications. Failure to adhere to
these codes and instructions may result in serious injury and/or property
damage and will void the warranty.
1) WARNING:Thisxtureisnottobeinstalledwithin10feet(3M)ofapool,
spa or fountain.
2) Thisxtureistobeusedonlywithapowerunit(transformer)rateda
 maximumof300W(25AMPS)15volts.
3) The#18ga.xturewireisnotintendedfordirectburial.
4) Direct burial rated wire is to be buried a minimum of 6” (152mm) beneath
the surface of the ground.
NOTE: If additional Direct Burial wire is needed, contact your local Kichler
®
landscape distributor.
 •8GAwirecanbepurchasedinlengthof250’(76M),15503-BK.
 •10GAwirecanbepurchasedinlengthof250’(76M),15504-BK.
 •12GAwirecanbepurchasedinlengthsof100’(30M),15501-BK;250’
  (76M),15502-BK;500’(152M),15505-BK;and1000’(304M),15506-BK.
5) Fixtureshallnotuseatungstenhalogenlampunlessthextureismarked
for use with such lamps.
6) Wiringconnectionsmustbemadewithapproved/listedwireconnection
 device(s)suitablefortheapplication.Donotexceedmanufacturers’wiring
 combinationspecicationsforsizeandquantityofconductors.
For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page
Para informacion de la garantia por favor visite: www.landscapelighting.com/portal/warranty_page
Date Issued: 12/2/11 IS-15073-US
QUIC DISC
™
WIRING INSTRUCTIONS
Turn off power.
Thefulllengthofthe18GAxturewiremaybeusedtoconnectwiththe10GAor12GAcableprovidedthefollowingconditionsaremet:
•Wiringistobeprotectedbyroutingclosetothextureoraccessoryorsecuredtoabuildingstructuresuchashouseordeck.
• 18GAxturewiringistobecutoffsothatitisattachedtotheconnectorwithin6inchesofthextureorbuildingstructure.
• Ifitisnecessarytomaketheconnectionsunderground,thennomorethan6inchesofthe18GAxturewireistobeburied.
The Quic Disc
™
connector is designed to install onextureandaccommodatesone18GAxturewireandone10GAorone12GAsupplywire.
Placethe10gaugesupplywireacrosstheareamarked10GAonQuicDisc
™
orplacethe12gaugesupplywireacrosstheareamarked12GA
on Quic Disc
™
.
Placethe18gaugexturewireacrosstheareamarked18GAontheQuicDisc
™
.Afterthewiresareinplace,connectathetopoftheQuic
Disc
™
tothebasewithsuppliedscrew,makingsurethatthewiresremainatinthebottomportionoftheQuicDisc
™
, and the screw is tightened
all the way down.
Thecoppercontactswillautomaticallypiercethewires’insulation.Excess18GAxturewirethatsticksouttheendoftheQuicDisc
™
is to be cut off.
Makenootherwiringconnectionstothe18GAxturewire.
SAVE THESE INSTRUCTIONS
INSTALLATION AND ASSEMBLY
Before Starting:
 A)Desiredlocationforeachxtureshouldbedeterminedbefore
construction of wall is started.
B) If access to back of wall is limited, cable/conduit should be run prior to
construction.
1) TURNOFFPOWER.
2) Assemblebracketstobottomofhousingusingwashersandscrews.
3) Knock off corner of brick on either side or below housing for cable/conduit
 entryandexit.
4) Screwsupplied1/2NPTplugsintoholesinhousingnotbeingusedfor
wire passage.
5) Remove socket bracket from inside of housing.
6) Mortarhousingintoplacenotingthefollowingitems:
 A)Supplywiremayneedtoberunintohousingatthistime,ifsopullsupply
wire through appropriate hole in housing and secure cable/conduit to
housing using a suitable connector.
 B)Embedlowerbracketsinmortar.
 C)Mortarhousingintoplaceasitifwereabrick.
 D)Allowmortartocurebeforewiringandre-assemblingbricklight.
7) Continuebuildingwall,installingremaininghousingasspeciedabove.
NOTE: Before the coarse of brick over housing is laid, attach brackets to top
of housing using washers and screws.
CAUTION:Whensecuringbrackets,donotapplyalotofpressureorforce.
This may damage uncured mortar.
8) Allowwalltocure.
9) Makewireconnections(connectorsnotprovided.)Thisxtureusesa
 non-polarizedsocket.Eachsupplywiremaybeconnectedtoeitherxture
wire.
10)Pushsocketbracketintohousingandsecureinplacewithscrews.
11) Insert recommended lamps.
12)Assemblecover/lenstohousing.
WASHER
ARANDELA
SCREW
TORNILLO
COVER/LENS
TAPA/LENTE
SOCKETBRACKET
APOYODELENCHUFE
BRACKET
APOYO
SCREW
TORNILLO
HOUSING
CUBIERTA