Installation Guide
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO
PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.
1) Turn off / unplug and allow to cool before replacing lamp.
2) Lamp gets HOT quickly! Contact only switch / plug when turning on.
3) Do not touch hot lens or cowl.
4) Do not remain in light if skin feels warm. (Light is intense, it may cause
“sunburn”.)
5) Do not look directly at lighted lamp.
6) Keep lamp away from materials that may burn.
7) Useonlywithwattageandlampmarkedonxture.
8) Do not touch the inner glass envelope of the lamp at any time. Use a soft
cloth. Oil from skin may damage lamp.
9) Donotoperatethexturewithadamagedormissinglens.
SAFETY INSTRUCTIONS
READ THIS FIRST
KEEP THESE INSTRUCTIONS
This xture is intended for installation in accordance with the National
Electric Code (NEC) and Local code specications. Failure to adhere to
these codes and instructions may result in serious injury and/or property
damage and will void the warranty.
1) WARNING:Thisxtureisnottobeinstalledwithin10feet(3M)ofapool,
spa or fountain.
2) Thisxtureistobeusedonlywithapowerunit(transformer)rateda
maximumof300W(25AMPS)15volts.
3) The#18ga.xturewireisnotintendedfordirectburial.
4) Direct burial rated wire is to be buried a minimum of 6” (152mm) beneath
the surface of the ground.
NOTE: If additional Direct Burial wire is needed, contact your local Kichler
®
landscape distributor.
•8GAwirecanbepurchasedinlengthof250’(76M),15503-BK.
•10GAwirecanbepurchasedinlengthof250’(76M),15504-BK.
•12GAwirecanbepurchasedinlengthsof100’(30M),15501-BK;250’
(76M),15502-BK;500’(152M),15505-BK;and1000’(304M),15506-BK.
5) Fixtureshallnotuseatungstenhalogenlampunlessthextureismarked
for use with such lamps.
6) Wiringconnectionsmustbemadewithapproved/listedwireconnection
device(s)suitablefortheapplication.Donotexceedmanufacturers’wiring
combinationspecicationsforsizeandquantityofconductors.
CAUTION
WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE),
CARE SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS.
WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES,
GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED ON THE LIGHT
BULB, LENS, OR BODY OF THE FIXTURE.
ASSEMBLY AND INSTALLATION
1) Wellxturecanbeinstalledtwodifferentways.
A) Ifxtureistobeusedfordirectuplighting,digholeinsoil15”deep.
B) Ifxtureistobeusedforwallwashing,digholeinsoil9-1/2”deep.
These dimensions will make hole large enough to accommodate
sleeveplus6”ofpeagravel.Toinsureproperdrainage,llbottomof
hole with 6” of pea gravel.
2) For direct uplighting set sleeve in deep hole with angled end down. For
wall washing set sleeve in shallow hole with angled end up.
3) Assemblerubberclipstoyokewithgrooveattopfacingcenter.
NOTE: One clip should always be assembled at back of yoke (where hook
is) then equally space the remaining two.
4) Connect wires to contacts on back of bulb and snap bulb into rubber clips.
5) Guidewirethroughbottomofsleeveandupalongtheoutsideofsleeve.
Setyokeintosleeveadjustingasneeded.
(NOTE: Hook on yoke has a short side and a long side, use short side with
yokeatacrossthetopforuplighting.Uselongsidewithyokeangledfor
wall washing purposes.
6) Fill gaps surrounding sleeve with soil.
7) Makewireconnectiontomainlowvoltagesupplywire.
Date Issued: 1/27/12 IS-15388-US
QUIC DISC
™
WIRING INSTRUCTIONS
Turn off power.
Thefulllengthofthe18GAxturewiremaybeusedtoconnectwiththe10GAor12GAcableprovidedthefollowingconditionsaremet:
•Wiringistobeprotectedbyroutingclosetothextureoraccessoryorsecuredtoabuildingstructuresuchashouseordeck.
• 18GAxturewiringistobecutoffsothatitisattachedtotheconnectorwithin6inchesofthextureorbuildingstructure.
• Ifitisnecessarytomaketheconnectionsunderground,thennomorethan6inchesofthe18GAxturewireistobeburied.
The Quic Disc
™
connector is designed to install onextureandaccommodatesone18GAxturewireandone10GAorone12GAsupplywire.
Placethe10gaugesupplywireacrosstheareamarked10GAonQuicDisc
™
orplacethe12gaugesupplywireacrosstheareamarked12GA
on Quic Disc
™
.
Placethe18gaugexturewireacrosstheareamarked18GAontheQuicDisc
™
.Afterthewiresareinplace,connectathetopoftheQuic
Disc
™
tothebasewithsuppliedscrew,makingsurethatthewiresremainatinthebottomportionoftheQuicDisc
™
, and the screw is tightened
all the way down.
Thecoppercontactswillautomaticallypiercethewires’insulation.Excess18GAxturewirethatsticksouttheendoftheQuicDisc
™
is to be cut off.
Makenootherwiringconnectionstothe18GAxturewire.
GROOVE
GARGANTA
BULB
BOMBILLA
RUBBERCLIP
ABRAZADERA
YOKE
HORQUILLA
UP-LIGHTINGSLEEVE
CAMISADEILUMINACION
HACIAARRIBA
WALL-WASHSLEEVE
CAMISADEILUMINACION
HACIAABAJODELAPARED
For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page
Para informacion de la garantia por favor visite: www.landscapelighting.com/portal/warranty_page