65" Maor 310136 A Kichler Decor ceiling fan ® Kichler® Lighting 7711 East Pleasant Valley Road P.O. Box 318010 Cleveland, Ohio 44131-8010 ™ Instruction Manual Customer Service 866.558.
1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control. Use only the control provided with the fan. 4.
65"Maor 2 2. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver 11 mm wrench Step ladder Wire cutters 3. PACKAGE CONTENTS Unpack your fan and check the contents . You should have the following items: A. Mounting Bracket B. Ball / Downrod Assembly (1) C. Canopy D. Canopy Hole Cover E. Coupling Cover F. Motor Body G. Blade Arm H. Blade Holder I. Blade J. Switch Housing K. Light Kit L. LED Module M. Glass Shade N. Light Case O.
3 4. MOUNTING OPTIONS If there isn't an existing ETL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Outlet box Fig. 1 Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 50 lbs). Do not use plastic outlet boxes.
65"Maor 4 5. HANGING THE FAN ETL Listed Outlet Box REMEMBER to turn off the power before you begin installation. This is necessary for your safety and also the proper programming of the control system. Ceiling Mounting Bracket Flat Washer Screw To properly install your ceiling fan, follow the steps below. Step 1. Before attaching fan to outlet box (not included), ensure the outlet box is securely fastened to at least two points to a structural ceiling member (a loose box will cause the fan to wobble).
5 Registration Slot Check Tab Step 5. Now lift the motor body into position and place the hanger ball into the hanger bracket. Rotate until the "Check Tab" has dropped into the "Registration Slot " and seats firmly. ( Fig. 9) The entire motor body should not rotate is this is done correctly. WARNING: Failure to properly seat the "Check Tab" can damage the ceiling fan during operation. Fig. 9 6 .
65"Maor 7. MAKE THE ELECTRIC CONNECTIONS WHITE WARNING: To avoid possible electrical shock, be sure you have turned off the power at the main circuit panel before wiring. BLACK SUPPLY CIRCUIT Outlet Box WHITE BLUE BLACK GREEN Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connector with electrical tape. Make sure there are no loose wire stands or connections.
7 Step 3. Securely attach and tighten the canopy hole cover over the shoulder screws in the mounting bracket utilizing the keyslot twist-lock feature. (Fig. 15) Shoulder Screw Canopy Hole Cover Fig. 15 9. ATTACHING THE FAN BLADES Blade Arm Blade Screw NOTE: Before continuing , make sure the power is disconnected by turning off the circuit breaker of removing the fuse at the circuit box. Step 1. Position the blade over the blade holder with three threaded posts showing.
65"Maor 8 10. INSTALLING THE SWITCH HOUSING Step 1. Remove the screw nearest the red dot label on the mounting ring and loosen the other two (do not remove). Let the 9-pin connector from motor body through the middle hole of switch housing. Align the two slot holes on the switch housing over the 2 screws previously loosened from the mounting ring. Turn the switch housing until it locks in place at the narrow end of the key holes. Securely tighten all three screws. (Fig.
9 12. INSTALLING THE GLASS SHADE AND LIGHT CASE Step 1. Assemble the glass shade to the light kit by twisting in a clockwise direction. Do not overtighten. (Fig. 21) Light Kit Glass Shade Fig. 21 Reverse Switch Step 2. Let the reverse switch and 2 pull chains through the holes on the light case. Attach the light case to the light kit by using the three flat head screws in hardware package. (Fig. 22) 13. INSTALLING THE FOB Step 1.
65"Maor 10 14. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check all electrical connections to insure proper contact. CAUTION: Make sure the main power is OFF when checking any electrical connection. 3. Make sure the transmitter batteries are installed properly. Positive (+) side facing out. 4. Insure the batteries have a good charge. Fan sounds noisy. 1. Make sure all motor housing screws are snug. 2.