Instructions / Assembly

ManualsBrandsKICHLER ManualsLightingEverly 15.25 in. 1-Light Natural Brass Modern Shaded Bell Kitchen Hanging Pendant Light with Clear Seeded Glass

For warranty information please visit: kichler.com/warranty

REV 26-JAN-2024

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

CAUTIONS

CAUTION – RISK OF SHOCK:

Disconnect Power at the main circuit breaker panel or main fusebox before

starting and during the installation.

WARNING:

1. This fixture is intended for installation in accordance with the National

Electrical Code (NEC) and all local code specifications. If you are not familiar

with code requirements, installation by a certified electrician is recommended.

Failure to adhere to these codes and instructions may result in serious injury

and/or property damage and will void the warranty.

CLEANING:

• Always be certain that electric current is turned o before cleaning.

• Only a soft damp cloth should be used. Harsh cleaning products may damage

the finish.

INSTALLATION INSTRUCTIONSFIXTURE DIAGRAM

IS-42199-US

PARTS LIST

[A] Outlet Box (Not

Supplied)

[B] Strap Mounting Screw

(2)

[C] Mounting Strap

[D] Mounting Screw (2)

[E] Canopy

[F] Lock Washer (2)

[G] Knob (2)

[H] Swivel (Attached to

Canopy)

[I] Stems (2-12”, 2-6” with

Short Threaded Tubes

[J] installed)

[J] Short Threaded Tubes

[K] Glass Shade Trim

[L] Stem Coupling

[M] Preinstalled Washer

[N] Rubber Gasket

[O] Steel Washer

[P] Glass Shade (shape

may be different than

what is shown)

[Q] Socket

[R] Slotted Coupling

NOTE: Thread locking compound must be applied to threads as noted with (4) symbol to

prevent accidental rotation of fixture during cleaning, relamping, etc.

1. Lower glass shade trim[K] down over stem coupling[L], and seat on preinstalled washer[M].

2. Pass fixture wires from stem coupling through desired number of short threaded tubes[J] and

stems[I]. Screw stems together using short threaded tubes.

Screw first stem into stem coupling.

NOTE: A minimum of one (1) 12-inch stem must be used when mounting fixture.

3. Pass fixture wires from last stem through end of swivel[H] and into canopy[E]. Thread the end of

swivel into end of last stem. Note direction of swivel in accordance with ceiling.

4. Cut fixture wires a MINIMUM of 6 inches from the top edge of canopy.

5. Find the appropriate threaded holes on mounting strap[C] that align with hole distance in

canopy. Assemble mounting screws[D] into threaded holes starting from the outlet box side.

6. Attach mounting strap to outlet box[A] using the supplied strap mounting screws[B]. Mounting

strap can be adjusted to suit position of fixture.

7. Grounding instructions: (See Illus. a or b).

a. On fixtures where mounting strap is provided with a hole and two raised dimples, wrap

ground wire from outlet box around green ground screw, and thread into hole.

b. On fixtures where a cupped washer is provided, attach ground wire from outlet box under

cupped washer and green ground screw, and thread into mounting strap.

If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with

wire connector after following the above steps. Never connect ground wire to black or white

power supply wires.

8. Make wire connections. Reference chart below for correct connections and wire accordingly.

Connect Black or Red

Supply Wire to:

Connect White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black without

Tracer

Clear, Brown, Gold or Black

with Tracer

Insulated wire (other than green) with

copper conductor

Insulated wire (other than green) with

silver conductor

*Note: When parallel wire (SPT 1 & SPT 2)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (See illus.)

Neutral Wire

9. Raise canopy to ceiling, carefully passing mounting screws through mounting screw holes in

canopy.

NOTE: Be certain wires do not get pinched between mounting strap and canopy or canopy and

ceiling.

10. While holding canopy in place, use lock washers[F] and knobs[G] to secure canopy. Tighten to

secure.

11. Carefully raise glass shade[P] up (over socket[Q] and slotted coupling[R]) to glass shade trim[K].

Carefully raise glass shade and glass shade trim together, above slotted coupling[R].

While holding glass shade and glass shade trim above slotted coupling, insert steel washer[O] into

the slot in the slotted coupling.

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

NOTE: Shape of included glass shade

may be dierent than what is shown here.

►

While holding glass shade and glass shade trim above slotted coupling, slip rubber gasket[N] onto

slotted coupling, and seat rubber gasket on top of steel washer.

Lower glass shade and glass shade trim, and seat glass shade on rubber gasket.

NOTE: When rubber gasket and steel washer are installed correctly, glass shade will seat between

glass shade trim and rubber gasket.

12. Insert recommended bulb(s). (Not supplied).

►

RUBBER GASKET[N]

STEEL WASHER[O]

SLOTTED COUPLING[R]

RUBBER GASKET[N]

SLIP ONTO SLOTTED

COUPLING. SEAT ON TOP OF

STEEL WASHER[O].

STEEL WASHER[O]

INSERT INTO THE SLOT IN THE

SLOTTED COUPLING.

Summary of content (3 pages)

PAGE 1
We’re here to help 866-558-5706 Hrs: M-F 9am to 5pm EST FIXTURE DIAGRAM INSTALLATION INSTRUCTIONS NOTE: Thread locking compound must be applied to threads as noted with (4) symbol to prevent accidental rotation of fixture during cleaning, relamping, etc. A B C D E F G 1. Lower glass shade trim[K] down over stem coupling[L], and seat on preinstalled washer[M]. 2. Pass fixture wires from stem coupling through desired number of short threaded tubes[J] and stems[I].
PAGE 2
Nous sommes là pour vous aider 866-558-5706 INSTRUCTIONS: For Assembling and Installing Fixtures in Canada Pour L’assemblage et L’installation Au Canada DIAGRAMME D’APPAREILS P P A B C D E F G INSTRUCTIONS D’INSTALLATION REMARQUE : Appliquer le frein filet sur les filets indiqués par le symbole (4) pour empêcher la rotation accidentelle du luminaire pendant le nettoyage, remplacement de lampe, etc. 1.
PAGE 3
J J ► ► INSTRUCCIONES DE INSTALACIÓN DIAGRAMA DE ACCESORIOS K K NOTA: Se debe aplicar compuesto de bloqueo de roscas a las roscas según lo indicado con el símbolo () para evitar la rotación accidental del artefacto durante la limpieza, el reemplazo de los focos, etc. A B C D E F G 1. Baje la guarnición de la pantalla de vidrio[K] sobre el acoplamiento del vástago[L], y asiéntela sobre la arandela preinstalada[M]. 2.