Installation Sheet

ManualsBrandsKichler ManualsChandeliersArmstrong 6 Light 20" Wide Sputnik Chandelier

Table Of Contents

Date Issued: 09/15/17 IS-43095-US

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel or main

fusebox before starting and during the installation.

1) Passxturewirefromthecoupling[1]ontopofxturethrough

astem[2]andscrewstemintocoupling.NOTE:One12”stem

isrequired.

NOTE: Threadlockingcompoundmustbeappliedtoallstem

threadsasnotedwitharrowsymboltopreventaccidentalrota-

tionofxtureduringcleaning,relamping,etc.

2) Passxturewirethroughdesiredamountofstemsandscrew

stemstogetherusingsuppliedshortthreadedtubes[3].

3) Passxturewirefromlaststemthroughrstloop[4].Thread

rstloopontoendoflaststem.

4) Passxturewirethroughsecondloop[5]andthroughholein

canopy.

5) (Ifsecondloopisalreadyattachedtocanopy,proceedtonext

step).Passthreadedpipeatendofsecondloopthroughhole

incanopy.Threadlockwasherontothreadedpipeprotruding

frominsidecanopy.Passxturewirethroughholeinhexnut

andthreadhexnutontoendofthreadedpipe.

6) Attachchainlink[6]tosmallloopatendofstemandtoloopon

canopy.

7) Findtheappropriatethreadedholesonmountingstrap[7].As-

semblemountingscrews[8]intothreadedholes.

8) Attachmountingstraptooutletbox[9].Themountingstrapcan

beadjustedtosuitpositionofxture.

9) Groundinginstructions:(SeeIllus.AorB).

 A) Onxtureswheremountingstrapisprovidedwithahole

andtworaiseddimples.Wrapgroundwirefromoutletbox

aroundgreengroundscrew,andthreadintohole.

 B) Onxtureswhereacuppedwasherisprovided.Attach

 groundwirefromoutletboxundercuppedwasherand

 greengroundscrew,andthreadintomountingstrap.

 Ifxtureisprovidedwithgroundwire.Connectxtureground

wiretooutletboxgroundwirewithwireconnector.(Notpro-

vided.)Afterfollowingtheabovesteps.Neverconnectground

wiretoblackorwhitepowersupplywires.

10)Makewireconnections(connectorsnotprovided.)Reference

chartbelowforcorrectconnectionsandwireaccordingly.

11) Pushxturetoceiling,carefullypassingmountingscrews

throughholesincanopy[10].NOTE:Becertainwiresdonot

getpinchedbetweencanopyandceiling.

12)Useknobs[11]andlockwashers[12]tosecurecanopy.Tighten

tosecure.

13) Insertrecommendedbulb(s)(Notsupplied).

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

►

Summary of content (2 pages)

PAGE 1
We’re here to help 866-558-5706 Hrs: M-F 9am to 5pm EST CAUTION – RISK OF SHOCK – Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation. 9 1) 2) 3) 4) 5) 6) 7) 8) 9) Pass fixture wire from the coupling [1] on top of fixture through a stem [2] and screw stem into coupling. NOTE: One 12” stem is required.
PAGE 2
Estamos aquí para ayudarle 866-558-5706 Horario: Lunes-Viernes 9am a 5pm EST (hora oficial del este) PRECAUCIÓN – RIESGO DE DESCARGA ELÉCTRICA – Desconecte la electricidad en el panel principal del interruptor automático o caja principal de fusibles antes de comenzar y durante la instalación. 1) 2) 3) 4) 5) 6) 7) 8) 9) Pase el cable de fijación del acoplamiento[1] en la parte superior del aparato a través del vástago[2] y enrosque el vástago en el acoplamiento. NOTA: Se requiere un tallo de 12 “.