Instruction Sheet

NOTE DIRECTION OF SWIVEL IN ACCORDANCE WITH CEILING.
1) Pass wire from fixture through stems and screw stems into
couplings on top of fixture body.
NOTE: Thread locking compound must be applied to all stem
threads as noted with symbol (3) to prevent accidental
rotation of fixture during cleaning, relamping, etc.
2) Pass fixture wire through remaining stems and screw stems
together.
3) Pass fixture wire through swivel attached to canopy. Thread
end of last stem onto swivel, pulling wires up through hole in
canopy.
4) Pass fixture wire through remaining swivel and thread end of
swivel onto end of last stem.
5) Pass threaded pipe on end of swivel up through hole in canopy,
pulling wires up through hole in canopy.
6) Slip lockwasher over end of wires and slip lockwasher over
end of threaded pipe protruding from inside canopy. Pass
wires through hole in wing nut. Screw wing nut onto end of
threaded pipe.
7) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room that
you are working on.
c) Place the wall switch in the “OFF” position. If the fixture to
be replaced has a switch or pull chain, place those in the
“OFF” position.
8) Thread hexnut onto threaded pipe so that 5 threads are
exposed above hexnut. Thread that end of the threaded pipe
into mounting strap and tighten hexnut against mounting
strap. Screw second hexnut onto end of threaded pipe
protruding from back of mounting strap.
9) Attach mounting strap to outlet box. (Screws not provided.)
10) Attach safety cable to slot in mounting strap.
11) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a hole
and two raise dimples. Wrap ground wire from outlet box
around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Put
ground wire from outlet box under cupped washer and
green ground screw and thread screw into hole in mounting
strap.
If fixture is provided with ground wire. Connect fixture ground
wire to outlet box ground wire with wire connector, (not
provided) after following the above steps. Never connect
ground wire to black or white power supply wires.
12) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
13) Push fixture to ceiling, carefully passing threaded pipe through
hole in canopy.
14) Thread hexnut onto end of threaded pipe protruding from
canopy. Tighten hexnut up against canopy.
15) Thread finial onto end of threaded pipe. (DO NOT over tighten.)
16) Set glass down over sockets.
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
IS-43186-US
Date Issued: 4/19/13
MOUNTING STRAP
PLANCHA PARA MONTAR
CANOPY
ESCUDETE
STEM
VARILLA
3
3
HEXNUT
TUERCA HEXAGONAL
FINIAL
REMATE
SAFETY CABLE
CABLE DE SEGURIDAD
COUPLING
ACOPLAMIENTO
SWIVEL
UNIÓN GIRATORIA
3
3
GLASS
VIDRIO
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
4
LOCKWASHER
ARNADELA DE SEGURIDAD
WING NUT
TUERCA DE MARIPOSA
HEXNUT
TUERCA HEXAGONAL