Installation Guide

IMPORTANT SAFETY INSTRUCTIONS
LIGHTED BULB IS HOT!
WARNING: To reduce the risk of FIRE or INJURY TO PERSON:
• Turn off and allow to cool before replacing bulb.
• Bulb gets HOT QUICKLY! Contact switch only when turning
off.
• DO NOT remain in light if skin feels warm. (Light is intense,
may cause “sunburn”)
• DO NOT look directly at lighted bulb.
• Keep materials away from bulb that may burn.
• Use ONLY with wattage specified or lower.
• DO NOT touch bulb at any time, use a soft cloth. Oil from skin
may damage bulb.
• DO NOT operate fixture with missing or damaged glass.
1) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
2) Thread hexnut onto threaded pipe so that 5 threads are
exposed below hexnut. From underside of mounting strap,
thread long end of threaded pipe into hole in mounting strap
until hexnut touches mounting strap. Tighten hexnut against
mounting strap.
3) Thread second hexnut onto other end of threaded pipe.
Tighten hexnut up against mounting strap.
4) Attach mounting strap to outlet box. (Screws not provided)
5) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a hole
and two raise dimples. Wrap ground wire from outlet
box around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never connect
ground wire to black or white power supply wires.
6) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
7) Push fixture to wall, carefully passing threaded pipe through
hole in canopy.
8) Screw threaded cap onto threaded pipe. Tighten threaded
cap to secure fixture to wall.
Date Issued: 9/4/15 IS-43375-US
MOUNTING STRAP
PLANCHA PARA MONTAR
GLASS
VIDRIO
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
THREADED CAP
TAPA ROSCADO
BULB
BOMBILLA
GLASS SLEEVE
CAMISA DE VIDRIO
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
9) Insert recommended bulb. CAUTION: DO NOT touch bulb
with bare hands. If this happens, clean bulb with denatured
alcohol and a lint free cloth.
10) Lower glass sleeve down over bulb. Carefully thread glass
sleeve onto socket. (DO NOT over tighten.)
11) Raise bottom trim up to fixture. Place top of bottom trim up
against bottom edge of canopy.
12) Align holes in bottom trim with holes in bottom of canopy.
Thread one screw up into each hole in bottom trim and into
each hole in canopy. Tighten screws to secure bottom trim
to canopy.
13) Set curved glass panel down on top of bottom trim. Fit
bottom edge of glass panel into channel on top of bottom trim.
14) Carefully place top trim on top of curved glass panel.
15) Align holes in top of top trim with holes along top of canopy.
Thread one screw down into each hole in top trim and into
each hole in canopy. Tighten screws to secure top trim to
canopy.
THREADED PIPE
TUBO ROSCADO
HEXNUT
TUERCA HEXAGONAL
BOTTOM TRIM
ADORNO INFERIOR
TOP TRIM
ADORNO SUPERIOR
SCREW
TORNILLO
SCREW
TORNILLO
CANOPY
ESCUDETE