Installation Sheet

IS-43496-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
5) Aer desired posion is found, ghten both top and
boom hexnuts up against the boom and top of the
mounng strap.
6) Slip canopy over screw collar loop and thread on
threaded ring. Aach chain[H] (with xture connected)
to boom of screw collar loop. Unscrew threaded ring,
let canopy and threaded ring slip down. Aach chain to
xture if required.
7) Weave electrical wire and ground wire through chain
links no more than 3 inches apart. Pass wire through
threaded ring[F], canopy, screw collar loop, threaded
pipe and into outlet box.
8) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, and thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector (Not provided) aer following the above steps.
Never connect ground wire to black or white power
supply wires.
9) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
10) Rotate the arms to the correct posions (Fig.1)
11) Thread wire through the top cap[P] and lower onto the
main body[K]
12) Raise canopy[G] to ceiling.
13) Secure canopy in place by ghtening threaded ring[F]
onto screw collar loop[B].
14) Thread in the threaded rod[L] into the boom of the top
of the main body as shown.
15) Place the trim cap[M] over the threaded rod and screw
on the nial[N] as shown.
16) Take threaded rod[L] and thread into the boom of the
main body as shown.
17) Take the boom cap[O] and place onto the boom of
the main body over the installed threaded rod.
18) Thread on the nial[N] to secure the boom in place.
19) Install the recommended bulbs (not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
1) Take threaded pipe[A] from parts bag and screw in screw
collar loop[B] a minimum of 6 mm (1/4”). Lock into place
with hexnut[C].
2) Run another hexnut down threaded pipe almost touching
rst hexnut. Now screw threaded pipe into mounng
strap[D]. Mounng strap must be posioned with
extruded thread faced into outlet box[E]. Threaded pipe
must protrude out the back of mounng strap. Screw
third hexnut onto end of threaded pipe protruding from
back of mounng strap.
3) Connect mounng strap to outlet box using the strap
mounng screws[J].
4) Unscrew the threaded ring[F] from screw collar loop.
Take canopy[G] and pass over screw collar loop.
Approximately one half of the screw collar loop exterior
threads should be exposed. Adjust screw collar loop by
turning assembly up or down in mounng strap. Remove
canopy.
Installaon Instrucons (connued)
[A] Threaded
Pipe
[B] Screw Collar
Loop
[C] Hexnut
[D] Mounting
Strap
[E] Outlet Box
[F] Threaded
Ring
[G] Canopy
[H] Chain
[I] Top Loop
[J] Strap
Mounting
Screws
[K] Main Body
[L] Threaded Rod
[M] Trim Cap
[N] Finial
[O] Bottom Cap
[P] Top Cap
E
D
C
J
A
G
B
F
H
I
P
K
L
M
N
L
O
N
Fig. 1