Kichler 43565 Instructions

1) Place bottom trim up against bottom of top arms.
2) Align holes in top of bottom trim with holes in top arms.
Thread screws down through holes in top arms and into
holes in bottom trim. Tighten screws to secure bottom trim
in place.
3) Pass wire from top of fixture body through stem. Thread end of
stem into hole in top of fixture body. NOTE: Thread locking
compound must be applied to all stem threads as noted
with symbol (3) to prevent accidental rotation of fixture
during cleaning, relamping, etc.
4) Pass fixture wire through remaining stems and screw stems
together.
5) Thread one small threaded pipe into end of each small loop.
6) Pass fixture wire through first loop. Thread first loop onto
end of last stem.
7) Pass fixture wire through second loop and through hole in
canopy.
8) Pass threaded pipe at end of second loop through hole in
canopy.
9) Pass fixture wire through hole in lockwasher. Thread
lockwasher onto end of threaded pipe protruding from
inside canopy.
10) Pass fixture wire through hole in hexnut. Thread hexnut onto
end of threaded pipe.
11) Attach chain link to small loop at end of stem and to loop on
canopy.
12) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
13) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
14) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
15) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
16) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
MOUNTING STRAP
ABRAZADERA DE MONTAJE
CANOPY
ESCUDETE
Date Issued: 10/3/14 IS-43565-US
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
KNURL KNOB
PERILLA ESTRADA
3
SMALL LOOP
ARGOLLA PEQUEÑA
3
CHAIN LINK
ESLABÓN DE CADENA
STEM
VASTAGO
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
17) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
18) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
19) Lower one glass diffuser down over each socket. Pass hole
in glass diffuser over socket.
20) Thread one socket ring onto each socket. Tighten socket
rings to secure diffusers in place. (DO NOT over tighten.)
21) Set one shade down on top of each diffuser.
22) Attach Crystal B to loop at end of each scroll.
23) Attach Crystal D to loop in top center of fixture body.
24) Attach Crystal C to loop in bottom center of fixture body.
SHADE
PANTALLA
GLASS DIFFUSER
DIFUSOR VIDRIO
CRYSTAL D
CRISTAL D
FIXTURE BODY
CUERPO DEL ARTEFACTO
CRYSTAL B
CRISTAL B
CRYSTAL C
CRISTAL C
SCREW
TORNILLO
SOCKET RING
ANILLO DEL
CASQUILLO