Installation Sheet

IS-43594-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Pass xture wire from the coupling[A] on top of xture
through a stem[B] and screw stem into coupling. NOTE:
One 12” stem is required. Thread locking compound
must be applied to all stem threads as noted with symbol
(4) to prevent accidental rotaon of xture during
cleaning, relamping, etc.
2) Pass xture wire through desired amount of stems and
screw stems together using supplied short threaded
tubes[C].
3) Pass xture wire from last stem through rst loop[D].
Thread rst loop onto end of last stem.
4) Pass xture wire through second loop[D] and through
hole in canopy.
5) (If second loop is already aached to canopy, proceed
to next step). Pass threaded pipe at end of second
loop through hole in canopy. Thread lockwasher onto
threaded pipe protruding from inside canopy. Pass
xture wire through hole in hexnut and thread hexnut[E]
onto end of threaded pipe.
6) Aach chain link[F] to small loop at end of stem and to
loop on canopy.
7) Find the appropriate threaded holes on mounng
strap[G]. Assemble mounng screws[H] into threaded
holes.
8) Aach mounng strap to outlet box[I] using the strap
mounng screws[M]. The mounng strap can be
adjusted to suit posion of xture.
9) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, then thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector (not provided.) aer following the above steps.
Never connect ground wire to black or white power
supply wires.
10) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (see illus.)
Neutral Wire
11) Push xture to ceiling, carefully passing mounng screws
through holes in canopy[J]. NOTE: Be certain wires do
not get pinched between canopy and ceiling.
12) Use knobs[K] and lockwashers[L] to secure canopy.
Tighten to secure.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
[A] Coupling
[B] Stem
[C] Short
Threaded
Tubes
[D] Loop
[E] Hexnut
[F] Chain Link
[G] Mounting
Strap
[H] Mounting
Screws
[I] Outlet Box
[J] Canopy
[K] Knobs
[L] Lockwashers
[M] Strap
Mounting
Screws
I
G
M
J
D
B
C
E
H
A
►
►
L
K
L
►
F
4 3594