Installation Sheet

IS-43596-US
Estamos aquí para ayudarle 866-558-5706
Horario: Lunes-Viernes 9am a 5pm EST (hora ocial del este)
protruding from inside of canopy. Pass xture wire
through lockwasher. Place lockwasher onto end of
threaded pipe protruding from inside of canopy. Pass
xture wire through hexnut[E].
6) (If second loop is already aached to canopy, proceed
to next step). Pass threaded pipe at end of second loop
through hole in canopy. Thread lockwasher[L] onto
threaded pipe protruding from inside canopy. Pass
xture wire through hole in hexnut and thread hexnut[E]
onto end of threaded pipe.
7) Aach chain link[F] to small loop at end of stem and to
loop on canopy.
8) Find the appropriate threaded holes on mounng
strap[G]. Assemble mounng screws[H] into threaded
holes.
9) Aach mounng strap to outlet box[I] using the strap
mounng screws[M]. The mounng strap can be
adjusted to suit posion of xture.
10) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, then thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector (not provided.) aer following the above steps.
Never connect ground wire to black or white power
supply wires.
11) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (see illus.)
Neutral Wire
12) Push xture to ceiling, carefully passing mounng screws
through holes in canopy[J]. NOTE: Be certain wires do
not get pinched between canopy and ceiling.
13) Use knobs[K] and lockwashers[L] to secure canopy.
Tighten to secure.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
[A] Coupling
[B] Stem
[C] Short
Threaded
Tubes
[D] First Loop
[E] Hexnut
[F] Chain Link
[G] Mounting
Strap
[H] Mounting
Screws
[I] Outlet Box
[J] Canopy
[K] Knobs
[L] Lockwashers
[M] Strap
Mounting
Screws
[N] Safety Cable
1) Pass xture wire from the coupling[A] on top of xture
through a stem[B] and screw stem into coupling. NOTE:
Thread locking compound must be applied to all stem
threads as noted with symbol (4) to prevent accidental
rotaon of xture during cleaning, relamping, etc.
2) Pass xture wire through desired amount of stems and
screw stems together using supplied short threaded
tubes[C].
3) Pass xture wire from last stem through rst loop[D].
Thread rst loop onto end of last stem.
4) Pass xture wire through second loop and through hole
in canopy[J].
5) Slip loop of safety cable[N] over end of threaded pipe
Installaon Instrucons (connued)
I
G
M
J
D
B
C
E
H
I
A
L
K
L
N

Summary of content (2 pages)