Installation Sheet

17) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
18) Raise canopy to ceiling.
19) Secure canopy in place by tightening threaded ring onto
screw collar loop.
20) Starting with Crystal C, slip hook at top of crystal through
hole along edge of ring. The pattern for the crystals is
Crystal C, Crystal N, Crystal H, Crystal N. Repeat this
pattern until all crystals are attached.
21) Attach one crystal sphere to the end of each crystal attached
to fixture.
22) Thread finial onto threaded pipe on bottom of fixture body.
1) Pass fixture wire from coupling on top of fixture body
through center stem. Thread end of center stem into
coupling.
3) Pass fixture wire from center stem through hole in short
threaded pipe. Screw end of threaded pipe into coupling on
top of center stem.
4) Pass fixture wire through hole in center of top trim. Lower
top trim down. Pass hole in center of top trim over end of
short threaded pipe in coupling.
5) Pass fixture wire through hole in bottom of loop. Thread loop
onto end of threaded pipe protruding from center of top trim.
6) Place fixture body inside ring.
7) Screw threaded cap at end of one cable to one threaded
pipe on top of ring. Repeat this step for remaining cables.
8) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
9) Take threaded pipe from parts bag and screw in screw collar
loop a minimum of 6 mm (1/4”). Lock into place with hexnut.
10) Run another hexnut down threaded pipe almost touching
first hexnut. Now screw threaded pipe into mounting strap.
Mounting strap must be positioned with extruded thread
faced into outlet box. Threaded pipe must protrude out the
back of mounting strap. Screw third hexnut onto end of
threaded pipe protruding from back of mounting strap.
11) Connect mounting strap to outlet box.
12) Unscrew the threaded ring from screw collar loop. Take
canopy and pass over screw collar loop. Approximately one
half of the screw collar loop exterior threads should be
exposed. Adjust screw collar loop by turning assembly up or
down in mounting strap. Remove canopy.
13) After desired position is found, tighten both top and bottom
hexnuts up against the bottom and top of the mounting
strap.
14) Slip canopy over screw collar loop and thread on threaded
ring. Attach chain (with fixture connected) to bottom of
screw collar loop. Unscrew threaded ring, let canopy and
threaded ring slip down.
15) Weave electrical wire and ground wire through chain links no
more than 3 inches apart. Pass wire through threaded ring,
canopy, screw collar loop, threaded pipe and into outlet box.
16) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 5/15/15 IS-43723-US
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
CRYSTAL C
CRISTAL C
CRYSTAL H
CRISTAL H
CRYSTAL N
CRISTAL N
MOUNTING STRAP
PLANCHA PARA MONTAR
LOOP
ANILLO
HEXNUT
TUERCA HEXAGONAL
THREADED PIPE
TUBO ROSCADO
THREADED RING
ANILLO ROSCADO
SCREW COLLAR LOOP
OJAL DE COLLAR
ROSCADO
CANOPY
ESCUDETE
CENTER STEM
VÁSTAGO CENTRAL
COUPLING
ACOPLAMIENTO
SHORT THREADED PIPE
TUBO ROSCADO CORTO
TOP TRIM
GUARNICIÓN SUPERIOR
CABLE
CABLE
THREADED CAP
TAPA ROSCADO
FIXTURE BODY
CUERPO DEL
ARTEFACTO
RING
ANILLO
CRYSTAL
CRISTAL
THREADED PIPE
TUBO ROSCADO
CRYSTAL SPHERE
ESFERA DE CRISTAL
FINIAL
CAPUCHÓN