Installation Sheet

Date Issued: 11/17/17 IS-44029-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fuse
box before starting and during the installation.
1) Take threaded pipe[1] from parts bag and screw in screw
collar loop[2] a minimum of 6 mm (1/4”). Lock into place with
hexnut[3].
2) Run another hexnut down threaded nipple almost touching
rst hexnut. Now screw threaded pipe into mounting strap[4].
Mounting strap must be positioned with extruded thread faced
into outlet box[5]. Threaded nipple must protrude out the back
of mounting strap. Screw third hexnut onto end of threaded
nipple protruding from back of mounting strap.
3) Connect mounting strap to outlet box.
4) Unscrew the threaded ring[6] from screw collar loop. Take
canopy[7] and pass over screw collar loop. Approximately
one half of the screw collar loop exterior threads should be
exposed. Adjust screw collar loop by turning assembly up or
down in mounting strap. Remove canopy.
5) After desired position is found, tighten both top and bottom
hexnuts up against the bottom and top of the mounting strap.
6) Slip canopy over screw collar loop and thread on threaded
ring. Attach chain[8] (with xture connected) to bottom of
screw collar loop. Unscrew threaded ring, let canopy and
threaded ring slip down. Attach chain to xture if required.
7) Weave electrical wire and ground wire through chain links no
more than 3 inches apart. Pass wire through threaded ring,
canopy, screw collar loop, threaded pipe and into outlet box.
8) Grounding instructions: (See Illus. A or B).
A) On xtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On xtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If xture is provided with ground wire. Connect xture ground
wire to outlet box ground wire with wire connector. (Not pro-
vided.) After following the above steps. Never connect ground
wire to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
4
3
1
7
6
2
8
9
18
15
16
17
10
3
13
3
14
11
12
OPTIONAL DOWNLIGHT SETUP
5
9) Make wire connections. Reference chart below for correct con-
nections and wire accordingly.
10) Raise canopy to ceiling.
11) Secure canopy in place by tightening threaded ring onto screw
collar loop.
12) Thread the threaded pipe[9] (with hex nut attached) into the
hickey[10] until the hex nut meets the hickey. To mount the
lights as a downlight option, follow step 13. If not, proceed
to step 14.
13) Loosen the hexnuts inside the wiring body[11] that support
each arm. Flip the arms with lights facing downward.
14) Raise the xture up to the threaded pipe.
15) Make wire connections, reference the chart on step 10. Be
sure the wires are inside the housing, and raise the wire body
into the top cap[12], passing the pipe through the hole in the
bottom.
16) Raise the bottom cap[13] to the wire body, and pass the hole
over the pipe.
17) Thread a hexnut[3] onto the threaded pipe. Tighten to secure.
18) Thread the nial[14] onto the threaded pipe, and tighten to
cover the hexnut.
19) Carefully raise glass[15] to the xture. Slip the smaller opening
over the socket[16] and rest the glass onto the socket cover[17].
20) Thread socket ring[18] onto socket. Tighten socket ring to
secure glass in place. (DO NOT over tighten.)
21) Insert recommended bulb (not supplied).
22) Repeat steps 19-21 for remaining sockets.