Installation Sheet

IS-44034-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
turning assembly up or down in mounng strap. Remove
canopy.
8) Aer desired posion is found, ghten both top and
boom hexnuts up against the boom and top of the
mounng strap.
9) Slip canopy over screw collar loop and thread on
threaded ring. Aach chain[H] (with xture connected)
to boom of screw collar loop. Unscrew threaded ring,
let canopy and threaded ring slip down.
10) Slide ring[I] down onto the top of the main body[L] over
the threaded pipe.
11) Aach decorave loop assembly[K] to top of main
body[L]. Aach chain to xture if required. Note that the
chain length can be changed by removing or adding links.
12) Weave electrical wire and ground wire through chain
links no more than 3 inches apart. Pass wire through
threaded ring, canopy, screw collar loop, threaded pipe
and into outlet box.
13) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, and thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector (Not provided) aer following the above steps.
Never connect ground wire to black or white power
supply wires.
14) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (see illus.)
Neutral Wire
15) Aach the support rod[O] the upper main body and to
the lower 6 light ring as shown.
16) Raise canopy to ceiling.
17) Secure canopy in place by ghtening threaded ring onto
screw collar loop.
18) Carefully lower glass[M] to the xture. Slip the smaller
opening over the socket and t the glass against the
socket.
19) Thread the socket ring[N] onto the socket. Tighten socket
ring to secure glass in place. (DO NOT over ghten).
20) Insert recommended bulb (Not supplied).
21) Rotate the three (3) hoops to the desired posion.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
[A] Threaded
Pipe
[B] Screw Collar
Loop
[C] Hexnut
[D] Mounting
Strap
[E] Outlet Box
[F] Threaded
Ring
[G] Canopy
[H] Chain
[I] Ring
[J] Strap
mounng
screws
[K] Decorave
loop
assembly
[L] Main body
[M] Glass
[N] Socket Ring
1) Place ring[I] onto center threaded tube of light
assembly[P].
2) Thread the center tube[O] onto the center threaded
tube of the light assembly.
3) Thread the completed center secon into the swivel of
the hoops.
4) Take threaded pipe[A] from parts bag and screw in
screw collar loop[B] a minimum of 6 mm (1/4”). Lock
into place with hexnut[C].
5) Run another hexnut down threaded pipe almost
touching rst hexnut. Now screw threaded pipe into
mounng strap[D]. Mounng strap must be posioned
with extruded thread faced into outlet box[E]. Threaded
pipe must protrude out the back of mounng strap.
Screw third hexnut onto end of threaded pipe protruding
from back of mounng strap.
6) Connect mounng strap to outlet box using the strap
mounng screws[J].
7) Unscrew the threaded ring[F] from screw collar loop.
Take canopy[G] and pass over screw collar loop.
Approximately one half of the screw collar loop exterior
threads should be exposed. Adjust screw collar loop by
Installaon Instrucons (connued)
E
D
C
J
A
G
B
F
H
K
L
N
M
O
P
I
I