Installation Sheet

IS-44110-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
**NOTE: A minimum of one 12 inch stem per side MUST be used in mounng of
xture.**
1) Pass wire through stems[A] and small threaded tubes[B] and screw stems
into couplings[Q] on top of xture body[P]. NOTE: Thread locking compound
must be applied to all stem threads as noted with symbol (4) to prevent
accidental rotaon of xture during cleaning,relamping, etc.
2) Pass xture wire through remaining stems and screw stems together.
3) On each side of xture, pass xture wire through one small threaded pipe[L].
Screw each small threaded pipe onto top of stem on each side.
4) On each side of xture, pass xture wires through each hole in canopy[H].
Lower canopy down towards stems. Pass each hole in canopy over end of
each threaded pipe on top of stems.
5) On one side of xture, pass xture wire through lockwasher[E]. Thread
lockwasher onto end of threaded pipe protruding from inside canopy. Pass
xture wire through hexnut[F]. Thread hexnut onto end of threaded pipe.
6) Slip loop on safety cable[D] over end of threaded pipe protruding from inside
of canopy. Pass xture wire through lockwasher. Thread lockwasher onto end
of threaded pipe protruding from inside canopy. Pass xture wire through
hexnut. Thread hexnut onto end of threaded pipe.
7) Find the appropriate threaded holes on mounng strap[G]. Assemble
mounng screws[N] into threaded holes.
8) Aach mounng strap to outlet box[C] using the strap mounng screws[I].
Mounng strap can be adjusted to suit posion of xture.
9) Aach safety cable to outlet box.
10) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole and two raised
dimples, wrap ground wire from outlet box around green ground screw,
and thread into hole.
b) On xtures where a cupped washer is provided, aach ground wire from
outlet box under cupped washer and green ground screw, and thread
into mounng strap.
If xture is provided with ground wire, connect xture ground wire to outlet
box ground wire with wire connector (Not provided) aer following the above
steps. Never connect ground wire to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
11) Make wire connecon. Reference chart below for correct connecons and
wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
12) Push xture to ceiling, carefully passing mounng screws through holes in
canopy. NOTE: Be certain wires do not get pinched between mounng strap
and canopy.
13) Secure xture to ceiling with lockwashers[J] and lock-up knobs[K] as shown.
14) Install the ve (5) long and the ve (5) short candle sleeves[O] onto the
correct sockets.
15) Insert recommended bulbs. (Not supplied)
Installaon Instrucons – Loop/Chain Link Mount
**NOTE: A minimum of one 12 inch stem per side MUST be used in mounng of
xture.**
1) Follow steps 1 and 2 from Rigid Stem Mount Instrucons.
2) Thread one small threaded pipe[L] into end of each small loop[R].
3) Pass xture wire through rst loop. Thread rst loop onto end of each last
stem.
4) On one side of xture, pass xture wire through second loop and through
hole in canopy[H]. Pass threaded pipe at end of second loop through hole in
canopy.
5) Pass xture wire through lockwasher[E]. Thread lockwasher onto end of
threaded pipe protruding from inside canopy.
6) Pass xture wire through hexnut[F]. Thread hexnut onto end of threaded
pipe.
7) On other side of xture, pass xture wire through second loop and through
hole in canopy. Pass threaded pipe at end of second loop through hole in
canopy.
8) Pass xture wire through loop on end of safety cable[D]. Slip loop on safety
cable over end of threaded pipe protruding from inside of canopy.
9) Pass xture wire through lockwasher. Thread lockwasher onto end of
threaded pipe protruding from inside canopy.
10) Pass xture wire through hexnut. Thread hexnut onto end of threaded pipe.
11) Aach locking linkto small loop at end of each stem and to each loop on
canopy and close the open chain link [M] by placing a piece of cloth over the
open link and using a pair of pliers gently squeeze the link closed.
12) Follow steps 7 - 15 from Rigid Stem Mount Instrucons.
Fixture Diagram
Parts List
[A] Stems
[B] Small Threaded Tubes
[C] Outlet Box
[D] Safety Cable
[E] Lockwasher
[F] Hexnut
[G] Mounting Strap
[H] Canopy
[I] Strap Mounting
Screws
[J] Lockwashwers
[K] Lock-up Knobs
[L] Small Threaded Pipe
[M] Chain Link
[N] Mounting Screws
[O] Candle Sleeves
[P] Fixture Body
[Q] Couplings
[R] Small Loops
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before
starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with the Naonal Electrical
Code (NEC) and all local code specicaons. If you are not familiar with code
requirements, installaon by a cered electrician is recommended.
Installaon Instrucons – Rigid Stem Mount
Installaon Instrucons – Rigid Stem Mount (connued)