Installation Sheet

CAUTION - RISK OF SHOCK: Disconnect power at the main
circuit breaker panel or main fuse box before starting and during
intallation.
1) Pass fixture wire through hole in bottom of one loop. Thread
loop onto threaded pipe on top of roof.
2) Thread small threaded pipe into end of second loop. Pass
threaded pipe on loop up through hole in canopy.
3) Thread lockwasher onto end of threaded pipe protruding
from inside canopy.
4) Thread hexnut onto threaded pipe protruding from inside
canopy.
5) Attach one end of chain to loop on top of roof. Attach other
end of chain to small loop on canopy.
6) Weave electrical wire and ground wire through chain links no
more than 3 inches apart.
7) Find the appropriate threaded holes on mounting strap that
align with hole distance in canopy. Thread mounting screws
into threaded holes starting from outlet box side.
8) Attach mounting strap to outlet box with strap mounting
screws. Mounting strap can be adjusted to suit position of
fixture.
9) Grounding instructions (see Illus. A or B):
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box between the cupped
washer and the green ground screw, and thread into
mounting strap.
If fixture is provided with ground wire, connect fixture ground
wire to outlet box ground wire with wire connector, after
following the above steps. Never connect ground wire to black
or white power supply wires.
10) Make wire connections. Reference chart below for correct
connections and wire accordingly.
11) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
12) Thread knurled lock-up knobs onto mounting screws.
Tighten knobs to secure fixture to ceiling.
13) Insert recommended bulb (not supplied).
14) Raise top of the cage up to inside of fixture roof.
15) Thread one screw from underneath the top of cage and into
holes in the fixture roof. Tighten screws to secure cage in
place.
NOTE: The glass comes with a vinyl gasket at the top and
bottom and needs to stay in place to prevent the glass from
rattling. DO NOT remove the vinyl gaskets from the glass.
Date Issued: June 29, 2017
IS-49689-US
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VERSIÓN EN ESPAÑOL EN EL REVERSO.
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Strap mounting
screws
Tornillos de montaje
de la abrazadera
Wire connectors
Conectores de cable
Outlet box
Caja de salida
Mounting strap
Abrazadera de montaje
Mounting screws
Tornillos de montaje
Lock-up knobs
Perillas de sujeción
Loop/Anillo
Chain/Cadena
Loop/Anillo
Roof/Techo
Bulb (not included)
Bombilla (no se incluye)
Cage
Jaula
Screws
Tornillos
Socket
Portalámparas
Canopy/Escudete