Specification Sheet

KichlerPro.com
Direct Wire Dimmable Power Supply
Direct Wire Dimmable Power Supply with
Wiring Compartments — No additional
NEMA enclosure required.
5 wire nuts, 2 mounting screws,
2 lid screws, 2 strain reliefs
Instruction Sheet
CONTENTS OF BOX
Part Number
Nominal AC Line
Voltage
(VAC)
Pout
Max
(W)
Pout
Min
(W)*
Vout
Max
(V)
Iout
Max
(V)
Vout
Regulation
4TD12V40BKT 120
40 12 12 3.3
11.64 - 12.36
(+/- 0.9V)
6TD24V10BKT 120 10 3 24 0.42
23.26 - 24.74
(+/- 1.8V)
6TD24V40BKT 120 40 12 24 1.7
23.26 - 24.74
(+/- 0.74V)
1 - ORDERING INFORMATION
2 - INPUT SPECIFICATION (at 25ºC AMBIENT TEMPERATURE)
Units Minimum Typical Maximum Notes
Input Voltage Range (Vin) Vac
108 120 132
-
Input Frequency Range Hz 47 60 63 When not used with a dimmer. (60 Hz +/- 3 when used with a dimmer)
Power Factor (PF) - 0.9 >0.9 - At nominal input voltage and full rated load
Inrush Current Meets NEMA-410 requirements At any nominal input full sine wave voltage and full rated load
Input Harmonics Complies with IEC61000-3-2 for Class C -
Total Harmonic
Distortion (THD)
- - - 20%
• At nominal input voltage and full rated load
• Complies with DLC (Design Light Consortium) technical requirements
Efficiency % -
85% (40W)
82% (10W)
- At nominal input voltage and full rated load
Isolation Meets UL60950-1 for class II reinforced/double insulation power supply
Standby Power W
- -
0.7 (40W)
0.6 (10W)
With no load
* Load must exceed Pout Min for proper operation. Pout Min is a typical value and may vary from unit to unit.
IS-xTD-LW-CB
We’re here to help 866- 558- 5706
Hrs: M-F 9am to 5 pm EST
Kichler 4TD12V40BKT, 6TD24V10BKT, 6TD24V40BKT Power Supplies
Installaon Instrucons
Fixture Diagram
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
BEFORE INSTALLING:
All installaons should comply with Naonal and local
Electrical codes.
If you have any doubts concerning installaon contact a
qualied licensed electrician.
CAUTION:
To reduce the risk of re, do not install closer than 1 inch to
cabinet wall or in compartment smaller than 12 inches by 12
inches by 12 inches.
Important Safety Instrucons
a) Read all instrucons.
b) Do not conceal or extend exposed conductors through a
building wall, oor or ceiling.
c) Install this system in dry or damp locaons only.
d) To reduce risk of re and burns, do not install this lighng
system where the exposed bare conductors can be
shorted or contact any conducve materials.
e) To reduce the risk of re and overheang, make sure all
connecons are ght
f) Do not install any luminaire closer than 6 inches (15.25cm)
from any curtain, or similar combusble materials.
g) Power supply has two disnct secons for line voltage
(AC Input) and low voltage (DC Output). It is important to
keep the line voltage and the low voltage wires separate.
h) Turn o electrical power before modifying the lighng
system in any way.
NOTE: Kichler 4TD-Series (12V) and 6TD-Series (24V) Power
Supplies are not compable with dimmers when used in
conjuncon with tape light controllers
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC
RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERANCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERANCE RECEIVED, INCLUDING INTERFERANCE THAT
MAY CAUSE UNDESIRED OPERATION.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smoo th)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (see illus.)
Neutral Wire
7) Total load of the installed lighng system must not
exceed rated waage of power supply.
NOTE: Aer determining the layout of the system,
add the waage of each luminaire/xture together to
calculate the total system consumpon. The calculated
total system consumpon should be equal or less than
the Class 2 power supply rang that is being used.
8) Using the pre-punched knock-outs in the metal
enclosure, route and connect the lighng system leads to
the secondary side (DC Output) of the power supply.
NOTE: Connect posive to the red wire and negave to
the black wire using the supplied wire nuts or other UL
approved connectors. Do not exceed manufacturers’
wiring combinaon specicaons for size and quanty of
conductors.
NOTE: A proper UL listed cable connector must be used
in the knock-outs to provide wire protecon (Connector
provided).
Cauons Installaon Instrucons (connued)
Installaon Instrucons
Save these instrucons
1) Turn o power.
2) Determine desired locaon for mounng power supply.
Power supply should be located within 25’ of rst luminaire.
3) Secure power supply using provided mounng screws.
Secure into wall studs if possible, otherwise; use
appropriate anchors rated for proper wall material and
hanging weight (Not included).
4) Using the pre-punched knock-outs in the metal
enclosure, route the 120V line voltage to the primary
side (AC Input) of the power supply.
NOTE: A proper UL listed cable connector must be
used in the knock-outs to provide strain relief and wire
protecon (Cable connector provided).
NOTE: When using cord and plug accessory (10193, not
provided), cord must be visible for enre run length.
5) Make grounding connecon (Connector provided).
6) Make wire connecons (Connectors provided).
Primary Side
Cable Connector
Secondary Side
Cable Connector
Primary Side
Wire Compartment
Secondary Side
Wire Compartment
Mounng Screw