Installation Guide

REV 05-JAN-2021 IS-52417-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
N
Q
F
P
O
P
R
►
►
►
►
D
I
G
H
M
►
C
K
J
A
A
B
L
E
Fixture Diagram
Parts List
[A] Stems
[B] Short Threaded
Tubes
[C] Swivel
[D] Canopy
[E] LED Driver
[F] Arm
[G] Mounting Strap
[H] Mounting Screws
[I] Outlet Box
[J] Knobs
[K] Lockwashers
[L] Coupling
[M] Strap Mounting
Screws
[N] Plate
[O] Lower Ring
[P] Chain Link
[Q] Knob
[R] Center Hub
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before
starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with the Naonal Electrical
Code (NEC) and all local code specicaons. If you are not familiar with code
requirements, installaon by a cered electrician is recommended.
DIMMING:
This LED xture is compable with most standard incandescent dimmers, LED
dimmers, and electronic low voltage dimmers.
For opmal performance, an electronic low voltage dimmer should be used.
CLEANING:
• Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning products may damage
the nish.
Installaon Instrucons
1) Aach arm[F] to lower ring[O] by aaching open chain link[P] to loop on
lower ring and to loop on end of arm. Close open chain link by placing a piece
of cloth over the open link and using a pair of pliers to gently squeeze the link
closed.
2) Screw knob[Q] into other end of arm inside center hub[R] and ghten to
secure arm in center hub.
3) Repeat for remaining arms.
4) Pass xture wires from center hub[R] through center hole of plate[N] and
slip plate over threads protruding from the top of the center hub.
5) Pass xture wires through coupling[L] and screw coupling onto threads
protruding through plate. Tighten to secure plate.
6) Pass xture wires from coupling[L] through desired number of stems[A] and
short threaded tubes[B]. Screw stems together using short threaded tubes.
NOTE: Thread locking compound must be applied to all stem threads as
noted with (4) symbol to prevent accidental rotaon of xture during
cleaning, relamping, etc.
7) Screw connected stems into coupling[L].
8) Pass xture wires from last stem through swivel[C] and into canopy[D].
9) Screw lower end of swivel into end of last stem.
Note direcon of swivel in accordance with ceiling.
10) Cut xture wires a MINIMUM of 6” from top edge of canopy.
NOTE: If the black and white driver lead wires must be trimmed, cut the wires
a MINIMUM of 6” from the top edge of canopy.
11) Connect the colored wires from the LED driver[E] to the wires from xture:
RED(+) from the LED driver to RED(+) from the xture and YELLOW(-) from the
LED driver to YELLOW(-) from the xture. Use smaller wire nuts (provided) to
secure wire connecons.
12) Find the appropriate threaded holes on mounng strap[G] that align with
hole distance in canopy[D]. Assemble mounng screws[H] into threaded
holes.
13) Aach mounng strap to outlet box[I] using the strap mounng screws[M].
Mounng strap can be adjusted to suit posion of xture.
14) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole and two raised
dimples, wrap ground wire from outlet box around green ground screw,
and thread into hole.
b) On xtures where a cupped washer is provided, aach ground wire from
outlet box under cupped washer and green ground screw, then thread
into mounng strap.
If xture is provided with ground wire, connect xture ground wire to outlet
box ground wire with wire connector aer following the above steps. Never
connect ground wire to black or white power supply wires.
15) Make wire connecon. Reference chart below for correct connecons and
wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
16) Push xture to ceiling, carefully passing mounng screws through holes in
canopy.
NOTE: Be certain wires do not get pinched between mounng strap and
canopy, or canopy and ceiling.
17) Use knobs[J] and lockwashers[K] to secure canopy. Tighten to secure.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
For warranty informaon please visit: kichler.com/warranty
BLACK AND WHITE LEAD
WIRES FROM DRIVER[E]
(+)RED FROM DRIVER[E]
(+)RED FROM FIXTURE
(-)YELLOW FROM
FIXTURE
(-)YELLOW FROM
DRIVER[E]
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause undesired operaon.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will
not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which
can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Informaon: