Instructions / Assembly

ManualsBrandsKICHLER ManualsLightingTopiary 1-Light Textured Black Vintage Cage Kitchen Pendant Hanging Light with Opal Glass Shade

For warranty information please visit: kichler.com/warranty

REV 12-NOV-2021

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

CAUTIONS

CAUTION – RISK OF SHOCK:

Disconnect Power at the main circuit breaker panel or main fusebox before

starting and during the installation.

WARNING:

1. This fixture is intended for installation in accordance with the National

Electrical Code (NEC) and all local code specifications. If you are not familiar

with code requirements, installation by a certified electrician is recommended.

Failure to adhere to these codes and instructions may result in serious injury

and/or property damage and will void the warranty.

CLEANING:

• Always be certain that electric current is turned o before cleaning.

• Only a soft damp cloth should be used. Harsh cleaning products may damage

the finish.

INSTALLATION INSTRUCTIONSFIXTURE DIAGRAM

IS-52464-US

PARTS LIST

[A] Short Threaded

Tubes (Attached to

Stems [G])

[B] Stems (2-12”, 2-6”

with Short Threaded

Tubes [F] installed)

[C] Swivel (Attached to

Canopy)

[D] Canopy

[E] Lock Washer (Qty. 2)

[F] Knob (Qty. 2)

[G] Strap Mounting

Screw (Qty. 2)

[H] Mounting Screw

(Qty. 2)

[I] Outlet Box (Not

Supplied)

[J] Mounting Strap

[K] Coupling

[L] Main Body

[M] Glass Shade

[N] Glass Shade

Retaining Ring

[O] Large Flat Washer

[P] Socket

[Q] Threads

1. Pass fixture wire from coupling[K] on top of main body through desired number of short threaded

tubes[A] and stems[B].

2. Screw stems together using short threaded tubes.

3. Thread assembled stems into coupling[K] on top of main body.

NOTE: Thread locking compound must be applied to all stem threads as noted with (4) symbol to

prevent accidental rotation of fixture during cleaning, relamping, etc.

4. Pass fixture wire from last stem through end of swivel[C] and into canopy[D]. Thread the end of

swivel into end of last stem. Note direction of swivel in accordance with ceiling.

5. Find the appropriate threaded holes on mounting strap[J] that align with hole distance in

canopy[D]. Assemble mounting screws[H] into threaded holes starting from the outlet box side.

6. Attach mounting strap to outlet box[I] using the supplied strap mounting screws[G]. Mounting

strap can be adjusted to suit position of fixture.

7. Grounding instructions: (See Illus. a or b).

a. On fixtures where mounting strap is provided with a hole and two raised dimples, wrap

ground wire from outlet box around green ground screw, and thread into hole.

b. On fixtures where a cupped washer is provided, attach ground wire from outlet box under

cupped washer and green ground screw, and thread into mounting strap.

If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with

wire connector after following the above steps. Never connect ground wire to black or white power

supply wires.

8. Make wire connections. Reference chart below for correct connections and wire accordingly.

Connect Black or Red

Supply Wire to:

Connect White Supply

Wire to:

Black White

*Parallel cord (round &

smooth)

*Parallel cord (square &

ridged)

Clear, Brown, Gold or Black

without Tracer

Clear, Brown, Gold or Black

with Tracer

Insulated wire (other

than green) with copper

conductor

Insulated wire (other

than green) with silver

conductor

*Note: When parallel wire (SPT

1 & SPT 2) are used. The neutral

wire is square shaped or ridged

and the other wire will be round

in shape or smooth (See illus.) Neutral Wire

9. Push fixture to ceiling, carefully passing mounting screws through holes in canopy.

NOTE: Be certain wires do not get pinched between mounting strap and canopy or canopy and

ceiling.

10. Use lock washers[E] and knobs[F] to secure canopy[D]. Tighten to secure.

11. Raise glass shade[M] into the center of main body[L]. Slip glass shade over socket[P] and

threads[Q], and fully seat glass shade into the main body.

12. While holding the glass shade in place, slip the large flat washer[O], then the glass shade retaining

ring[N] over the socket[P] and up to the threads[Q]. Tighten the shade retaining ring to the

threads to secure large flat washer and glass shade to main body. DO NOT OVER-TIGHTEN.

13. Insert recommended bulb. (Not supplied).

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

►►

Summary of content (3 pages)

PAGE 1
We’re here to help 866-558-5706 Hrs: M-F 9am to 5pm EST FIXTURE DIAGRAM INSTALLATION INSTRUCTIONS I 1. Pass fixture wire from coupling[K] on top of main body through desired number of short threaded tubes[A] and stems[B]. G 2. Screw stems together using short threaded tubes. 3. Thread assembled stems into coupling[K] on top of main body.
PAGE 2
Nous sommes là pour vous aider 866-558-5706 INSTRUCTIONS: For Assembling and Installing Fixtures in Canada Pour L’assemblage et L’installation Au Canada INSTRUCTIONS D’INSTALLATION DIAGRAMME D’APPAREILS I G J H E ► F 1. Passez le fil du luminaire depuis l’accouplement[K] par le nombre souhaité de tubes filetés courts[A] et de tiges[B]. 2. Vissez les tiges ensemble à l’aide de tubes filetés courts. 3. Vissez les tiges assemblées dans l’accouplement[K] en haut du corps principal.
PAGE 3
Estamos aquí para ayudarle 866-558-5706 Horario: Lunes-Viernes 9am a 5pm EST (hora oficial del este) INSTRUCCIONES DE INSTALACIÓN DIAGRAMA DE ACCESORIOS I 1. Pase el cable del artefacto desde el acoplamiento[K] en la parte superior del cuerpo principal a través del número deseado de tubos roscados cortos[A] y vástagos[B]. G 2. Enrosque los vástagos entre sí utilizando los tubos roscados cortos. 3. Enrosque los vástagos armados en el acoplamiento[K] en la parte superior del cuerpo principal.