Instructions / Assembly

ManualsBrandsKICHLER ManualsLightingKarthe 3-Light Natural Brass Hallway Wall Sconce Light

For warranty information please visit: kichler.com/warranty

REV 4-NOV-2021

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

CAUTIONS

CAUTION – RISK OF SHOCK:

Disconnect Power at the main circuit breaker panel or main

fusebox before starting and during the installation.

WARNING:

1. This fixture is intended for installation in accordance

with the National Electrical Code (NEC) and all local

code specifications. If you are not familiar with code

requirements, installation by a certified electrician is

recommended. Failure to adhere to these codes and

instructions may result in serious injury and/or property

damage and will void the warranty.

CLEANING:

• Always be certain that electric current is turned o before

cleaning.

• Only a soft damp cloth should be used. Harsh cleaning

products may damage the finish.

INSTALLATION INSTRUCTIONS

FIXTURE DIAGRAM

IS-52473-US

PARTS LIST

[A] Mounting

Strap

[B] Outlet Box

[C] Strap

Mounting

Screw (2)

[D] Countersunk

Mounting

Screw (2)

[E] Canopy

1. Pass supply wires through center hole in mounting strap[A].

2. Attach mounting strap to outlet box[B] using the strap mounting

screws[C]. Mounting strap should be mounted with the threaded holes

at the far edges of the mounting strap in the 12 and 6 o’clock position.

3. Grounding instructions: (See Illus. a or b).

a. On fixtures where mounting strap is provided with a hole and two

raised dimples, wrap ground wire from outlet box around green

ground screw, and thread into hole.

b. On fixtures where a cupped washer is provided, attach ground wire

from outlet box under cupped washer and green ground screw, and

thread into mounting strap.

If fixture is provided with ground wire, connect fixture ground wire to

outlet box ground wire with wire connector after following the above

steps. Never connect ground wire to black or white power supply wires.

4. Make wire connections. Reference chart below for correct connections

and wire accordingly.

Connect Black or Red

Supply Wire to:

Connect White Supply

Wire to:

Black White

*Parallel cord (round &

smooth)

*Parallel cord (square &

ridged)

Clear, Brown, Gold or Black

without Tracer

Clear, Brown, Gold or Black

with Tracer

Insulated wire (other

than green) with copper

conductor

Insulated wire (other

than green) with silver

conductor

*Note: When parallel wire (SPT

1 & SPT 2) are used. The neutral

wire is square shaped or ridged

and the other wire will be round

in shape or smooth (See illus.) Neutral Wire

5. Push fixture to wall, carefully aligning the threaded holes in the top

and bottom of mounting strap[A] with holes in the top and bottom of

canopy[E].

NOTE: Fixture should be mounted with candles in the up position. Make

sure all wires are inside canopy and do not get pinched between wall and

canopy of fixture.

6. Screw two (2) countersunk mounting screws[D] into the holes in the

canopy and mounting strap to attach fixture to wall. One at the top and

one at the bottom. Tighten to secure.

7. Insert recommended bulbs (not included).

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Summary of content (3 pages)

PAGE 1
We’re here to help 866-558-5706 Hrs: M-F 9am to 5pm EST INSTALLATION INSTRUCTIONS FIXTURE DIAGRAM D 1. Pass supply wires through center hole in mounting strap[A]. 2. Attach mounting strap to outlet box[B] using the strap mounting screws[C]. Mounting strap should be mounted with the threaded holes at the far edges of the mounting strap in the 12 and 6 o’clock position. 3. Grounding instructions: (See Illus. a or b). A B C a.
PAGE 2
INSTRUCTIONS: For Assembling and Installing Fixtures in Canada Pour L’assemblage et L’installation Au Canada D A 1. Faites passer les fils d’alimentation à travers le trou central de l’étrier de montage[A]. 2. Fixez l’étrier de montage sur la boîte de sortie[B] avec les vis de montage de l’étrier[C]. L’étrier de montage doit être installé avec les trous filetés sur les bords éloignés de la sangle de montage en position 12 et 6 heures. 3. Connecter les fils.
PAGE 3
Estamos aquí para ayudarle 866-558-5706 Horario: Lunes-Viernes 9am a 5pm EST (hora oficial del este) INSTRUCCIONES DE INSTALACIÓN DIAGRAMA DE ACCESORIOS D A B 1. Pase los cables de alimentación a través del orificio central de la abrazadera de montaje[A]. 2. Fije la abrazadera de montaje a la caja de salida[B] utilizando los tornillos de montaje de la abrazadera[C].