Specification Sheet

ManualsBrandsKichler ManualsLighting24 Volt 60 Watt 0 -10V Dimming LED Driver

Ground (GRN)

0-10V Dimmable Power Supply

Nominal Input

Voltage

Max Output

Power

Output

Voltage

Output

load Min

120-277 VAC

90W

60W

24V CV

Output

Current Max

Efficiency

Max Ambient

Temperature

THD

3.75A (24V, 90W)

2.5A (24V, 60W)

> 88%

typical

40º C

<20%

Power Factor

Dimming

Range

Startup Time

>0.9

1.5-100% of

light output

< 500 ms

CV: Constant Voltage

24V 90W and 24V 60W Constant Voltage LED Drivers 8TD24V060BKT, 8TD24V090BKT

90W & 60W Power Supply with wiring compartments.

No additional NEMA enclosure required.

YEAR

WARRANTY

FEATURES & BENEFITS

• 0-10V dimming control links multiple low-voltage fixtures

together and allows different fixtures to respond at once

• 120-277 Input Voltage to specify, stock and use one power

supply, regardless of the job

• Compact size allows for more placement flexibility

• All-in-one drive and box meets NEC Code

APPLICATIONS

• 8T or 6T Series 24V LED Tape

• As a system with 8T or 6T Series 24V Tape

and Extruded Aluminum Channels

• 6D Series 24V LED Accent Discs

24 VDC

LED Array/Fixture

Direct

Wire

Power

Supply

V+ (Red)

V- (Blue)

DIM+ (PURPLE)

DIM- (GREY)

120 VAC-

277VAC

L (BLK)

N (WHT)

Typical Application and Wiring Diagram

Summary of content (8 pages)

PAGE 1
0-10V Dimmable Power Supply 24V 90W and 24V 60W Constant Voltage LED Drivers 8TD24V060BKT, 8TD24V090BKT Typical Application and Wiring Diagram 120 VAC277VAC L (BLK) 24 VDC Direct V+ (Red) Wire V- (Blue) Power N (WHT) Supply LED Array/Fixture DIM+ (PURPLE) DIM- (GREY) 90W & 60W Power Supply with wiring compartments. No additional NEMA enclosure required.
PAGE 2
0-10V Dimmable Power Supply 1 - ORDERING INFORMATION Part Number Nominal AC Line Voltage (VAC) Pout Max (W) Pout Min (W)* Vout Max (V) Iout Max (V) Vout Regulation 8TD24V090BKT 120-277 90 3 24 3.75 23.28-24.72 (+/- 0.72V) 8TD24V060BKT 120-277 60 3 24 2.5 23.28-24.72 (+/- 0.72V) * Load must exceed Pout Min for proper operation. Pout Min is a typical value and may vary from unit to unit.
PAGE 3
0-10V Dimmable Power Supply 3 - OUPUT SPECIFICATION (at 25ºC AMBIENT TEMPERATURE) Units Minimum Typical Maximum Notes Output Voltage (Vout) Vdc - 24 - - Output Current (Iout) A 0 - 3.75 A 2.5A Output Voltage Regulation % - +/- 3.0 - Output Voltage Overshoot % - - 20 Output Current Ripple ≤ 15% output current ripple for each model Measured at nominal input voltage Dimming Range % 1.
PAGE 4
0-10V Dimmable Power Supply 5 - EMC COMPLIANCE AND SAFETY APPROVALS EMC Compliance Conducted and Radiated EMI FCC CFR Title 47 Part 15 Class B at 120 VAC and FCC CFR Title 47 Part 15 Class A at 277 VAC Harmonic Current Emissions IEC61000-3-2 - Voltage Fluctuations & Flicker IEC61000-3-3 - Immunity Compliance Transient Protection ESD (Electrostatic Discharge) IEC61000-4-2 6kV contact discharge, 8kV air discharge, level 3 RF Electromagnetic Field Susceptibility IEC61000-4-3 3V/m, 80 - 1000 MHz,
PAGE 5
0-10V Dimmable Power Supply 7 - INSTALLATION Figure 1 8 - DIMMING For recommended dimmers, visit Kichler.com/dimming. Kichler.
PAGE 6
0-10V Dimmable Power Supply 9 - VOLTAGE DROP CHARTS For best performance and lumen output, ensure proper wire gauge is installed to compensate for voltage drop of low voltage circuits. 24V VOLTAGE DROP CHART 5W 0.21A 10W 0.42A 20W 0.83A 30W 1.25A 40W 1.67A 50W 2.08A 60W 2.5A 70W 2.92A 80W 3.33A 90W 3.75A 100W 4.17A 18 AWG 261 ft. 130 ft. 65 ft. 43 ft. 32 ft. 26 ft. 21 ft. 18 ft. 16 ft. 14 ft. 13 ft. 16 AWG 401 ft. 200 ft. 100 ft. 66 ft. 50 ft. 40 ft. 33 ft. 28 ft. 25 ft.
PAGE 7
0-10V Dimmable Power Supply 10 - MECHANICAL DETAILS Packaging: Metal case for all variations. I/O Connections: Flying leads, 18 AWG on both AC and DC connections, insulation rated minimum 90°C, 300V, stripped and tinned. There is a ground wire attached to the metal enclosure. 11 - OUTLINE DRAWINGS Figure 2 3169056 2.6 8.7 1.4 12 - LABELING The 8TD24V060BKT is used in Figure 3 as an example to illustrate a typical label.
PAGE 8
0-10V Dimmable Power Supply 13 - SAFETY WARNINGS / DISCLOSURES 1. Install in accordance with national and local electrical code regulations. 2. This product is intended to be installed and serviced by a qualified, licensed electrician. 3. NEC code 725. 136: Class 1 and Class 2 circuits in same enclosure must be separated by a barrier unless Class 2 circuit conductors are installed in accordance with 725.41 Class 1 circuits. For example, Non Metallic (NM) cable is considered a Class 1 circuit conductor.