Instructions / Assembly

ManualsBrandsKichler ManualsLightingLED Canless Recessed Light 4" Recessed Trim - IC Rated - 2700K

IS-DLSL03R-US

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

Fixture Diagram

Parts List

[A] Fixture

[B] Junction Box

[C] Quick Screw Lock

Connector

[D] Fixture Cable

Connector

[E] Junction Box Cable

Connector

[F] Junction Box Cover

[G] Strain Relief

Connector

[H] Push-In Wire

Connectors

[I] Spring Clips

Installaon Instrucons

INSTALLATION HOLE SIZES:

DLSL03R xtures (3" Round xtures)

DLSL03R SERIES xtures require a round installaon hole at least 3-5/8" (92mm) in

diameter.

DLSL04R xtures (4” Round xtures)

DLSL04R SERIES xtures require a round installaon hole at least 4-1/4” (108mm) in

diameter.

DLSL05R xtures (5” Round xtures)

DLSL05R SERIES xtures require a round installaon hole at least 5-1/2” (140mm) in

diameter.

DLSL06R xtures (6" Round xtures)

DLSL06R SERIES xtures require a round installaon hole at least 6-1/4" (159mm) in

diameter.

1) Disconnect juncon box[B] from xture[A] by unscrewing quick screw lock

connector[C], then carefully pulling apart xture cable connector[D] from juncon

box cable connector[E].

Cauons

CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel or main fusebox before starng and

during the installaon.

WARNING:

This xture is intended for installaon in accordance with the Naonal Electrical Code

(NEC) and all local code specicaons. If you are not familiar with code requirements,

installaon by a cered electrician is recommended.

Supply wires are not intended for use through or concealed behind walls, oors, or

ceilings.

The LED light output is strong enough to injure human eyes. Precauons must be taken

to prevent looking directly at LED’s with unaided eyes for more than a few seconds.

DIMMING:

This LED xture is compable with phase cut dimmers only. For listed compable

dimmers, see www.kichler.com

CLEANING:

• Always be certain that electric current is turned o before cleaning.

• Only a so damp cloth should be used. Harsh cleaning

products may damage the nish.

1) Read and understand all instrucons and illustraons completely before proceeding

with assembly and installaon of xture.

2) If you have any doubts about how to install this xture, or if the xture fails to

operate completely, please contact a qualied electrician.

3) All parts must be used as indicated in the instrucons. Do not substute any parts,

leave parts out, or use any parts that are worn or broken. Failure to obey this

instrucon could invalidate the UL lisng, C.S.A. cercaon, and/or ETL lisng of this

xture.

4) Fixture is to be connected to a single branch circuit.

This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference that may cause undesired operaon.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will

not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which

can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separaon between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Informaon:

For warranty informaon please visit: kichler.com/warranty

2) Open juncon box cover[F] and remove preferred juncon box knockout using a

at-head screwdriver.

3) Pass Romex supply cable through included strain relief connector[G] and into

juncon box through knockout hole. Secure in place using strain relief connector.

4) Connect ground wire from Romex supply cable to green xture ground wire using

included push-in wire connector[H].

5) Make the remaining wire connecons using included push-in wire connectors.

Reference chart below for correct connecons and wire accordingly.

Connect Line

(Black or Red Supply Wire) to:

Connect Neutral

(White Supply Wire) to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear without Tracer Clear with white Tracer

*Note: When parallel wire (SPT 1 & SPT 2) are used. The

neutral wire is square shaped or ridged and the other wire

will be round in shape or smooth (See illus.)

Neutral Wire

6) Aer wire connecons are made, place all wires inside juncon box and close cover,

being careful not to pinch any of the wires between the juncon box and cover.

7) Raise juncon box through installaon hole and into the ceiling.

NOTE: If installing to new construcon, mount juncon box to a nearby joist, stud,

or similar xed structural unit with the included mounng screws.

For remodeling applicaons, juncon box may rest on top of ceiling material. This

xture and juncon box are Type IC rated and suitable for use in direct contact with

insulaon.

8) Reconnect xture cable connector to juncon box cable connector, lining up arrows

on the connectors while pressing them together. Secure connecon by screwing on

quick screw lock connector.

9) Carefully push spring clips[I] upward while raising xture to the installaon hole.

10) Slowly release spring clips as xture enters installaon hole so that spring clips begin

to make contact with top edge of ceiling material. Be careful not to pinch ngers

between spring clips and xture, or xture and ceiling while installing. Spring clips

will pull xture up the rest of the way to ceiling, mounng the xture in place.

NOTE: Ensure that spring clips have pulled the xture ush to the ceiling.

Installaon Instrucons (connued)

E D

I I

D E

Summary of content (3 pages)

PAGE 1
We’re here to help Fixture Diagram 866-558-5706 Hrs: M-F 9am to 5pm EST Installation Instructions (continued) 2) 3) H H 4) H 5) F B Open junction box cover[F] and remove preferred junction box knockout using a flat-head screwdriver. Pass Romex supply cable through included strain relief connector[G] and into junction box through knockout hole. Secure in place using strain relief connector.
PAGE 2
Nous sommes là pour vous aider 866-558-5706 INSTRUCTIONS: For Assembling and Installing Fixtures in Canada Pour L’assemblage et L’installation Au Canada Diagramme D’appareils Heures : du lundi au vendredi, de 9h à 17h (heure de l’Est) Instructions D’installation (suite) 2) H 3) H 4) H 5) F B G Ouvrez le couvercle de la boîte de jonction[F] et retirez l’alvéole défonçable de la boîte de jonction avec un tournevis à tête plate.
PAGE 3
Estamos aquí para ayudarle 866-558-5706 Horario: Lunes-Viernes 9am a 5pm EST (hora oficial del este) Diagrama de Accesorios Instrucciones de Instalación (continuación) 2) H 3) H 4) H 5) F B G Abra la tapa de la caja de empalmes[F] y retire el agujero ciego preferido de la caja de empalmes utilizando un destornillador plano. Pase el cable de alimentación Romex a través del conector de alivio de tensión proporcionado[G] y hacia el interior de la caja de empalmes a través del agujero ciego.