8" POLA WALL FAN Product images may vary slightly from actual product INSTRUCTION MANUAL
KICHLER.
TABLE OF CONTENTS SAFETY RULES..................................................................4 TOOLS AND MATERIALS REQUIRED..................................5 PACKAGE CONTENTS........................................................5 MOUNTING BASE ON A WOOD FRAMED WALL................6 MOUNTING PIPE AND BASE ASSEMBLY..........................6 WALL MOUNT BRACKET / MOTOR ASSEMBLY...............7 MOTOR / REAR GRILLE AND BLADE ASSEMBLY...............7 FRONT GRILLE ASSEMBLY....................................
SAFETY RULES CAUTION: Read and follow all instructions before operating fan. Do not use if any part is damaged or missing. WARNING: To reduce the risk of fire or electrical shock, DO NOT use this fan with any solid state speed control device. This appliance has a 3-prong grounded plug that must be inserted into a matching outlet. To reduce the risk of electrical shock, this grounding plug must not be cut off the plug.
TOOLS REQUIRED PACKAGE CONTENTS • • • • • Unpack your fan and check the contents.
ASSEMBLY Mounting Base on a Wood Framed Wall 1. 2. 3. Locate a wall stud secure and solid enough to hold the weight of the base assembly. Carefully locate and mark the center of the wall stud. If you do not have a solid structural framing member at that location then you must provide an adequate alternative for mounting the fan. Place mounting bracket (4) against the wall centered with the centerline of the wall stud and 4 holes.
Wall Mount Bracket / Motor Assembly Front Grille Assembly 1. 1. 2. 3. 4. 5. Remove the 2 bolts (11), washers (10) and nuts (12) from the wall mount / pipe (7). Align the holes on the pipe with the holes in the motor flange on the motor assembly. Insert the bolts (11) and replace the washers and nuts removed in step 1. Adjust the tilt to the desired positionand tighten the pivot knob (8) to set the angle. Tighten the position bolt and nut. CAUTION: Be sure to secure the knob. 2. 3. 4.
OPERATING INSTRUCTIONS CLEANING 1. WARNING: Unplug from electrical supply source before cleaning. After servicing, any safety device (including grills and blades) must be reinstalled or remounted as previously installed. Use soft damp cloth then wipe with dry cloth. Do not use harmful cleaners. Do not bend the blades. 2. 3. Change the setting on the speed control to the desired operating speed.
www.kichler.com KICHLER® LIGHTING 7711 EAST PLEASANT VALLEY ROAD P.O. BOX 318010 CLEVELAND, OHIO 44131-8010 CUSTOMER SERVICE 866.558.
VENTILADOR DE PARED POLA, 45.
2 KICHLER.
TABLA DE CONTENIDO NORMAS DE SEGURIDAD...............................................................4 HERRAMIENTAS Y MATERIALES NECESARIOS..............................5 CONTENIDO DEL PAQUETE.............................................................5 MONTAJE DE BASE EN PARED CON MARCO DE MADERA.........6 MONTAJE DE TUBO Y ENSAMBLAJE DE BASE.........................6 SOPORTE DE MONTAJE EN PARED/ENSAMBLAJE DEL MOTOR...7 ENSAMBLAJE DE MOTOR/REJILLA TRASERA Y ASPA..................
NORMAS DE SEGURIDAD PRECAUCIÓN: Lee y sigue todas las instrucciones antes de poner en funcionamiento el ventilador. No uses el ventilador si alguna de las piezas está dañada o en falta. ADVERTENCIA: Para reducir el riesgo de incendio o descarga eléctrica, NO utilices este ventilador con ningún dispositivo de estado sólido para control de velocidad . Este electrodoméstico tiene un enchufe de 3 clavijas con conexión a tierra, que tiene que insertarse en un tomacorriente adecuado.
HERRAMIENTAS NECESARIAS CONTENIDO DEL PAQUETE • • • • • Desempaca tu ventilador y revisa el contenido. Debes tener los siguientes artículos: Destornillador Phillips Destornillador para aspas Llave de 11 mm Escalera de tijera Cortacables • • • • Ensamblaje del motor Rejilla frontal/trasera y aspa Base y tubo de montaje en la pared Manual del usuario y paquete de herrajes VENTILADOR DE PARED POLA, 45.
ENSAMBLAJE Montaje de base en pared con marco de madera 1. 2. 3. Localiza una viga de pared suficientemente segura y sólida para sostener el peso del ensamblaje de la base. Ubica y marca con cuidado el centro de la viga de pared. Si no hay un elemento de enmarcado estructural sólido en el lugar, tienes que buscar una alternativa adecuada para instalar el ventilador. Coloca el soporte de montaje (4) contra la pared, centrado con la línea central de la viga de pared y 4 orificios.
Soporte de montaje en pared / Ensamblaje del motor Ensamblaje de rejilla frontal 1. 1. PRECAUCIÓN: Asegúrate de ajustar la perilla. Por último, instala en el soporte de montaje su cubierta decorativa (1). Quita los 2 pernos (11), arandelas (10) y tuercas (12) del montaje de pared / tubo (7). 2. Alinea los orificios del tubo con aquellos en la brida del motor sobre su ensamblaje. 3. Inserta los pernos (11) y vuelve a colocar las arandelas y tuercas retiradas en el paso 1. 4.
INSTRUCCIONES DE USO LIMPIEZA 1. ADVERTENCIA: Antes de limpiarlo desenchúfalo de la fuente de suministro eléctrico. Luego del mantenimiento, todos los dispositivos de seguridad (incluyendo las rejillas y aspas) tienen que reinstalarse tal y como estaban antes. Usa un paño suave húmedo y pasa enseguida uno seco. No uses limpiadores que puedan causar daños. No dobles las aspas. Cambia la configuración del control de velocidad a la velocidad de funcionamiento que desees.
www.kichler.com ILUMINACIÓN KICHLER® 7711 EAST PLEASANT VALLEY ROAD P.O. BOX 318010 CLEVELAND, OHIO 44131-8010 SERVICIO AL CLIENTE: 866.558.5706 DE LUNES A VIERNES, DE 8:30 AM A 5:00 PM (ESTE) VENTILADOR DE PARED POLA, 45.