Owner Manual

To Connect
1. Open connector gently using your
finger nail.
2. Slide tape light into front of connector
making sure that the tape is kept
flat when placed in the connector’s
guides. Gently push the tape light
forward until the tape light is fully
seated in the connector and is under
the prongs.
Note: Check that the connection is
secure and that polarity (+/-) symbols
are oriented in the same direction.
3. Close connector.
4. Remove 3M backing from tape light
and apply making sure to press
between the LED’s and other
components. Pressing on the
LED’s and other components will
result in damage to the tape.
Note: For best results, peel off backing
and apply tape light in small sections
starting at the beginning of the run.
Note: Avoid using excessive force to
prevent damage to LEDs and other
components.
6. Install any additional sections of tape
light and connectors in the same
manner.
7. Connect power supply lead to power
supply and turn on.
Note: Before powering on the system,
double check that all connections are
secure and that all polarity (+/-) symbols
are oriented in the same direction.
Best Practices...
Kichler® tape light incorporates many
installer friendly features such as plug-
and-play power supplies and tape light
with 3M brand adhesive backing. In
addition to these included features,
Kichler offers a large variety of
additional accessories to make
installations even easier.
Installation Instructions
For Use in Dry Locations Only
All installations should comply with
national and local electrical codes. If you
have any doubts concerning installation,
contact a qualified, licensed electrician.
Supply leads and interconnects are not listed
for In Wall use. Read all instructions
thoroughly before starting installation.
•This fixture can only be used with
Kichler® LED Tape Lighting drivers and
accessories. This fixture must be
connected to a NRTL Listed Class 2, 24V
DC power supply.
• Voltage drop limits the linear run length
of 24V DC fixtures, and these lengths
differ between the products listed below.
a.6T1xxSxxxx = 32 feet (Standard)
b.6T1xxHxxxx = 20 feet (High)
c.6T1xxYHxxxx = 10 feet (Ultra High)
•Total wattage of tape light should
not exceed power supply wattage.
To determine the total wattage of
tape light, multiply the total number
of feet used by the wattages listed
below for the appropriate tape light
type.
a. 6T1xxSxxxx = 1.5 W/ft. (Standard)
b. 6T1xxHxxxx = 3 W/ft. (High)
c. 6T1xxUHxxxx = 7.2 W/ft. (Ultra High)
*
Maximum linear run length is determined
using a 96W power supply & a 1’ power
supply lead with a continuous
linear run of LED tape light.
Please contact Kichler’s Advanced
Technical Support team for questions
about the maximum run length at
[e-mail].
Pre Installation Checklist
• Prepare the location that the LED tape
light will be installed. Make sure that
the area has been thoroughly cleaned
and is dry. If installing underneath a
cabinet, it is recommended to install
tape light at least 1-1/2" away from
cabinet lip to prevent shadowing on
counter top surface.
• Determine location for power supply
and length of supply lead wire that
will be needed.
• Determine how many sections of tape
light and different lengths of connectors that
will be needed.
Installation
1. Install power supply.
Note: The power supply should be
installed by a qualified electrician and be
installed in accordance with national and
local electric codes. Refer to the power
supply installation instructions for further
detail.
2. Run supply lead wire from power
supply to beginning of tape light run.
Do not connect lead wire to power
supply yet.
3. Measure and if necessary, cut the
first section of tape light, leaving a
minimum of one inch of space on
each end for connections.
Note: To cut the tape light, use a pair of
sharp scissors or snips and cut on the
dotted cut line only.
4. Completely remove 1/4" of the
adhesive backing from either end of
the tape that will be inserted into the
connector.
Caution: If the adhesive backing is not
removed, this may cause damage to the
connector.
5. Connect tape light to supply lead wire.
Note: Make sure +/- symbols on tape
light line up with the +/- symbols on the
connector of the supply lead wire.
Kichler Lighting
www.kichler.com
Phone [phone]
7711 E. Pleasant Valley Road
PO Box 318010
Cleveland, Ohio 44131-8010
24V LED Tape Light