LIVIN’ LOUD ZX AMPLIFIER ZX700.5 English Version Versión Español Amplificador del la Serie ZX.5 Deutsche Version Stereoverstärker der ZX.5-Serie Version Francaise Amplificateur de série ZX.
ZX.5-SERIES AMPLIFIERS Owner’s Manual MODEL: ZX700.5 Authorized KICKER Dealer: Purchase Date: Model Number: Serial Number: PERFORMANCE RMS Power: AMP1 & AMP2 channels driven @ 14.4V, 4 stereo, d 1% THD+N @ 14.4V, 2 stereo, d 1% THD+N @ 14.4V, 4 mono, d 1% THD+N 70W x 4 85W x 4 165W x 2 RMS Power: SUBWOOFER channel driven @ 14.4V, 4 mono, d 1% THD+N @ 14.
The ZX amplifier has dual input sensitivity differential RCA inputs which will receive either high or low level signals from your car stereo’s source unit. Ideally, when connecting the source unit to the amplifier, the ZX amplifier’s input level switch should be set to “LO” and a low-level signal should run from the source unit’s stereo RCA output to the stereo RCA input on the end panel of the amplifier using RCA interconnect cable.
FOUR CHANNEL OPERATION with SUBWOOFER minimum impedance of 2 ohms per channel (AMP1, AMP2, and SUB channels) signal in AUTO TURN ON +12V DC L AUDIO XOVER1 XOVER2 OFF OFF HI R INPUT SUB LEVEL FADER INPUT HI AMP1 1 R L L AMP2 LO HI OFF ON AMP1 SUB R 2 SUB L+ L- R+ R- REMOTE BASS + SUB - signal in woofer ZXRC* REMOTE BASS INSTALLATION 2. slide the housing until it snaps into the metal bracket back view 1.
OPERATION AUTO TURN ON +12V DC L AUDIO XOVER1 XOVER2 OFF OFF HI R R INPUT SUB LEVEL FADER INPUT HI AMP1 INPUT 1 L L AMP2 INPUT LO HI OFF ON AMP1 SUB R 2 L+ L- R+ R- SUB INPUT REMOTE BASS + SUB - Automatic Turn-On Selection: The ZX series offers three different automatic turn-on modes that can be selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode causes the REM terminal to have +12V out for turning on additional amplifiers.
TROUBLESHOOTING If your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is an illuminated red badge on top of the amplifier denoting the power state of the amp in addition to the Protection LED on the end panel of your KICKER ZX series amplifier. When the red badge is lit, this indicates the amplifier is turned on and the amplifier is functioning properly.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper connections can result in blown amplifier fuses as well as the failure of other critical systems in the vehicle. If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on the KICKER homepage, www.kicker.com.
ELECTRONICS LIMITED WARRANTY KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of THREE (3) MONTHS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer it is warranted for TWO (2) YEARS from date of original purchase with receipt. In all cases you must have the original receipt.
INTERNATIONAL WARRANTY Contact your International KICKER dealer or distributor concerning specific procedures for your country’s warranty policies. WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at the same volume level.
©2009 Stillwater Designs
