KX Amplifiers KX MONO AMPLIFIERS KX400.1 | KX800.1 | KX1200.1 | KX1600.1 | KX2400.1 Owner’s Manual | English Manual del Propietario | Español AMPLIFICADOR DEL LA SERIE KX.1 Benutzerhandbuch | Deutsch MONOVERSTÄRKER DER KX.1-SERIE Manuel d’utilisation | Française AMPLIFICATEUR DE SÉRIE KX.
KX.1-SERIES AMPLIFIERS OWNER’S MANUAL MODEL: KX400.1 / KX800.1 / KX1200.1 / KX1600.1 / KX2400.1 Authorized KICKER Dealer: Purchase Date: Model Number: Serial Number: PERFORMANCE Model: KX400.1 KX800.1 KX1200.1 KX1600.1 KX2400.1 RMS Power @ 14.4V, 4 mono, d 1% THD+N @ 14.4V, 2 mono, d 1% THD+N 200W x 1 400W x 1 400W x 1 800W x 1 600W x 1 1200W x 1 800W x 1 1600W x 1 Length | in [cm] 8 [20.4] 9 9/16 [24.4] 9 9/16 [24.4] 11 3/16 [28.4] 15 1/2 [39.
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid, metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the battery’s negative post and the vehicle chassis is recommended.
MONO OPERATION minimum impedance of 2 ohms woofer d18” (45cm) external fuse d24” (60cm) 12V battery remote turn-on (see page 5) bare-metal chassis ground bare-metal chassis ground 4
OPERATION Mini-USB for internal use only; do NOT remove or tamper. KICKER is not responsible for any damage to equipment resulting from connections made to this port. Automatic Turn-On Selection: The KX series offers three different automatic turn-on modes that can be selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode causes the REM terminal to have +12V out for turning on additional amplifiers.
KXRC REMOTE BASS INSTALLATION Surface-mount the KXRC remote using the supplied screws. back view Connect the supplied cable to the KXRC remote and the Remote Bass jack on the amplifier TROUBLESHOOTING If your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is a Protection (PRT) LED on the side panel of your Kicker KX series amplifier.
If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on the KICKER homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab, choose the subject you are interested in, and then download or view the corresponding information. Please E-mail support@kicker.com or call Technical Services (405) 624-8583 for unanswered or specific questions. KX400.
ELECTRONICS LIMITED WARRANTY When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase with receipt. If this product is identified as “Refurbished” or “B Goods”, the warranty is limited to a period of THREE (3) MONTHS from the date of original purchase. In all cases you must have the original receipt.
INTERNATIONAL WARRANTY Contact your International KICKER dealer or distributor concerning specific procedures for your country’s warranty policies. WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at the same volume level.
©2012 Stillwater Designs
