CX Amplifiers CX SERIES MONO AMPLIFIERS CXA300.1 | CXA600.1 | CXA1200.1 | CXA1800.1 Owner’s Manual | English Manual del Propietario | Español AMPLIFICADOR DEL LA SERIE CX.1 Benutzerhandbuch | Deutsch MONOVERSTÄRKER DER CX.1-SERIE Manuel d’utilisation | Française AMPLIFICATEUR DE SÉRIE CX.
CX.1-SERIES AMPLIFIERS OWNER’S MANUAL CXA300.1 | CXA600.1 CXA1200.1 | CXA1800.1 MODEL: Authorized KICKER Dealer: Purchase Date: Model Number: Serial Number: WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at the same volume level.
VERTICAL MOUNTING amplifier end panel hex screws double-slotted bracket Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid, metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the battery’s negative post and the vehicle chassis is recommended.
MONO OPERATION minimum impedance of 2 ohms woofer ≤18” (45cm) ≤24” (60cm) external fuse 12V battery remote turn-on (see page 5) bare-metal chassis ground 12V bare-metal chassis ground ≤18” (45cm) external fuse For multiple amplifier installations where distribution blocks are used, each amplifier should have its proper-rated fuse, or breaker, installed between the amplifier and the distribution block within eighteen inches of the block, or on the distribution block if it provides for fusing.
Model External Fuse Power/Ground Wire KICKER Wiring Kit (sold separately) CXA300.1 1 x 40 Ampere 8 Gauge PK8, ZCK84 CXA600.1 1 x 80 Ampere 4 Gauge PK4, CK44, ZCK44 CXA1200.1 1 x 150 Ampere 4 Gauge PK4, CK44, ZCK44 CXA1800.1 1 x 150 Ampere 1/0 Gauge PKD1, PWB050 OPERATION Automatic Turn-On Selection: The CX series offers two different automatic turn-on modes; +12V and DC Offset.
CXARC REMOTE BASS INSTALLATION Surface-mount the CXARC remote using the supplied screws. back view Remote cable passes audio; do not run cable parallel to power wires. Connect the supplied 1/8th inch [3.5mm] patch cable to the CXARC remote and the Remote Bass jack on the amplifier TROUBLESHOOTING If your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc.
Ground Noise? KICKER amplifiers are engineered to be fully compatible with all manufacturers’ head units. Some head units may require additional grounding to prevent noise from entering the audio signal. If you are experiencing this problem with your head unit, in most cases running a ground wire from the RCA outputs on the head unit to the chassis will remedy this issue. CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct.
ELECTRONICS LIMITED WARRANTY When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase with receipt. If this product is identified as “Refurbished” or “B Goods”, the warranty is limited to a period of THREE (3) MONTHS from the date of original purchase. In all cases you must have the original receipt.
INTERNATIONAL WARRANTY Contact your International KICKER dealer or distributor concerning specific procedures for your country’s warranty policies. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
©2015 Stillwater Designs
CXA1200.1 5/N: MODEL NUMBER SERIAL NUMBER CERTIFIED POWER TOTALPOWER OUTPUT [WATTS RMS] 127'6 .·,., ._ .. I pa.
