CX Amplifiers CX MULTI-CHANNEL AMPS CXA600.5 Owner’s Manual | English Manual del Propietario | Español AMPLIFICADOR DEL LA SERIE CX.5 Benutzerhandbuch | Deutsch VERSTÄRKER DER CX.5-SERIE Manuel d’utilisation | Française AMPLIFICATEUR DE SÉRIE CX.
CX.5-SERIES AMPLIFIERS OWNER’S MANUAL MODEL: CXA600.5 Authorized KICKER Dealer: Purchase Date: Serial Number: WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at the same volume level. The threshold of pain is always an indicator that the sound level is too loud and may permanently damage your hearing.
INSTALLATION Mounting: Choose a structurally sound location to mount your KICKER amplifier. Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier. The KICKER CX Amplifiers are capable of space-saving vertical mounting. Use a 2.
source unit high-level speaker outputs to amplifier core conductor KICKER KISL (optional) OR + – to amplifier shield from source unit highlevel speaker outputs Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifier. If you ever need to remove the amplifier from the vehicle after it has been installed, the ground wire should be the last wire disconnected from the amplifier--just the opposite as when you installed it.
12V For multiple amplifier installations where distribution blocks are used, each amplifier should have its proper-rated fuse, or breaker, installed between the amplifier and the distribution block within eighteen inches of the block, or on the distribution block if it provides for fusing.
OPERATION audio inputs Automatic Turn-On Selection: The CX series offers two different automatic turn-on modes; +12V and DC Offset. • Remote Turn-On: Run 18 gauge wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM between the amplifier’s positive and negative power terminals. This is the preferred automatic turn-on method. • DC Offset Turn-On: The DC Offset mode detects a 6V DC offset from the HI-Level speaker outputs when the source unit has been turned on.
CXARC REMOTE BASS INSTALLATION (CXARC not included.) Surface-mount the CXARC remote using the supplied screws. back view Remote cable passes audio; do not run cable parallel to power wires. Connect the supplied 1/8th inch [3.
Ground Noise? KICKER amplifiers are engineered to be fully compatible with all manufacturers’ head units. Some head units may require additional grounding to prevent noise from entering the audio signal. If you are experiencing this problem with your head unit, in most cases running a ground wire from the RCA outputs on the head unit to the chassis will remedy this issue. CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct.
ELECTRONICS LIMITED WARRANTY When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase with receipt. If this product is identified as “Refurbished” or “B Goods”, the warranty is limited to a period of THREE (3) MONTHS from the date of original purchase. In all cases you must have the original receipt.
HOW LONG WILL IT TAKE? KICKER strives to maintain a goal of one week turnaround for all electronics (amplifiers, crossovers, equalizers, etc.) returns. Delays may be incurred if lack of replacement inventory or parts is encountered. Failure to follow these steps may void your warranty. Any questions can be directed to the KICKER Customer Service Department at (405) 624-8510. Contact your International KICKER dealer or distributor concerning specific procedures for your country’s warranty policies.
©2015 Stillwater Designs
., L: :: ,:,:· i' : - ~' -~ '<. ." CXA600. 5 MODEL NUMBER SERIAL NUMBER CERT IFIED POW ER TOTALPOWE R OUTPUT [WATTS RMS] 0 ,. .,.
