PO H PWER PO 5 O KIT I E D U A S A TS S I R LA ® R Z R ® R O SP pg 2 pg 9 pg 13 pg 25 pg 29 Disassembly, Wire and Amplifier Plate Installation Glovebox Subwoofer Installation Kick Panel Speakers Installation Cage Mount Speakers Installation MRB3 and Dash Kit Installation
44PRZ35 Polaris RZR XP 1000 & 900 Kicker 5 Speaker Audio Kit WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All Kicker Speakers are covered by a limited 1 year warranty against defects in material or workmanship.
PANELS AND DASH DISASSEMBLY A A. Remove all seats by releasing the handle behind each seat, push forward slightly while lifting up. B B. Disconect the negative battery cable from the battery. C C. Remove hood by turning locking pins and lifting up. D D D. Remove center dash by unscrewing the 2 T-30 Torx screws and push center dash forward to unclip. E E. Disconnect all harness connectors attached to the center dash panel. F F. Un-pin and pull to remove the passenger side safely handle.
PANELS AND DASH DISASSEMBLY G1 G2 G3 G. Remove the factory dash pocket by first extracting the 10mm bolt on the dash frame (G1). Then pull out the dash pocket with bracket attached (G2) - NOTE this bracket will no longer be used for any part of this installation. Save this screw as it will be use later during the amp plate installation. Extract (2) screws securing the sub dash (G3). Unsnap and remove. H H H H. Remove all of the center console push pins and T-30 Torx screws.
RUNNING AMP POWER CABLE AND REAR SPEAKER WIRE A B A. Unwrap the tape and pull the rubber wire grommet out of the firewall. B. Pull the MRB3 POWER and GROUND wires through the rubber grommet and feed through the hole in the firewall to the power strip located on the opposite side of the firewall. NOTE C1 C2 C. From under the hood, against the top firewall, unscrew the nut on the first position terminal (12v accessory) and attach the yellow POWER wire. Refasten on the nut (C1).
RUNNING AMP POWER CABLE AND REAR SPEAKER WIRE E TOP VIEW E UNDERNEATH VIEW E E. Route the front speaker wire through the opening where the firewall and roll cage bar meet on both the driver and passenger side. Leave these wires loose until the front speaker pods are to be installed.
RZR XP1000 & 2015+ RZR900 Kicker 10” Glove Box Subwoofer Enclosure WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All Kicker Speakers are covered by a limited 1 year warranty against defects in material or workmanship.
B A A. Remove the ten T40 Torx bolts that secure the 2 piece fender. Note: there is one screw inside the fender well. Remove the two additional screws from the striker plate, slide fender up the cage rail and secure C B. Remove the two 10mm bolts that secure factory glove box and remove the factory glove box C C. Lift the enclosure into place and align the top channel in the grab handle bar.
G G. For 2015-up model year vehicles, install the supplied bracket using the short screws provided and adjust forward or back so glove box latch closes tight H H. For 2014 model year vehicles remove the factory glove box door latch. Mount the latch to the supplied bracket and secure to the enclosure using the short screws provided I I. Route the speaker wire away from any moving parts and any sharp metal, then connect to the amplifier. J J.
RZR XP1000 & 2015+ RZR900 Kicker 6.5” Speaker Front Kick Panels WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All Kicker Speakers are covered by a limited 1 year warranty against defects in material or workmanship.
A A. Using the utility knife or another cutting tool cut off the two plastic factory nubs in the foot well, cut these as smooth as you can to the panel. NOTE: If pod does not come pre-installed with speaker, do not use provided paper templates. Use the pod mounting holes as your drill template. Hold the pod in position and mark the drill holes through the empty pod using a scribe tool. All pilot holes will be drilled from the inside footwell. B1 B2 B3 B4 B.
C1 C2 C. Drill a pilot hole at the places just marked with a 1/8” drill bit. Then follow up by using a 1/4” drill bit in the lower pilot hole (for mounting the pod) and a 1/2” drill bit in the upper pilot hole (for speaker cable). D1 E1 D4 D2 D3 D5 D. Cut out the OUTSIDE template (Driver/Passenger) along the cut line. Position the template on the outside footwell. Make sure the bottom of the template lines up along the bottom edge and tab of the factory panel as shown in figure D1-D3.
E1 E2 E. Drill a pilot hole at the places just marked with a 1/8” drill bit. Then follow up by using a 1/4” drill bit for both pilot holes (for mounting the pod). F G F. Route the speaker cable attached to the pod through the inside footwell 1/2” hole made in Step D. G. Position the speaker pod in place and line up with drilled mounting holes H H H. With the provided M6 screws and washers, loosely mount the pod through the 3 holes previously drilled.
RZ3-F65 2017 Polaris RZR Kick Pod, Cut Template Driver Outside Template Drill Point Drill Point Cut along parimeter 17
Drill Point RZ3-F65 2017 Polaris RZR Kick Pod, Cut Template Passenger Inside Template Cut along parimeter Drill Point 19
RZ3-F65 2017 Polaris RZR Kick Pod, Cut Template Passenger Outside Template Drill Point Drill Point Cut along parimeter 21
RZ3-F65 2017 Polaris RZR Kick Pod, Cut Template Driver Inside Template Cut along parimeter Drill Point Drill Point 23
Universal Cage Mount Kicker 6.5” Speaker Enclosures WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All Kicker Speakers are covered by a limited 1 year warranty against defects in material or workmanship. All Kicker Amplifiers are covered by a limited 2 year warranty against defects in material or workmanship.
A A. Find the best orientation for the speaker on your bar and screw in the Set Screws in the OPPOSITE holes of where the clamp will install into. C B B. Loosely install the clamp base to the cage mount pod with the two (2) M6 hex head bolts and washers, place the cage mount pod in the desired mounting location on the vehicle. Once the ring adapter is in the desired position, tighten the two (2) bolts using a 8mm open wrench. C C C.
D D. From the rear of the center console, route the B-H1150 harness up to each speaker pod and connect. E E. Route the speaker wire away from any moving parts and any sharp metal, then connect to the amplifier F F.
Polaris RZR XP 1000 & 900 Dash Kit for MRB3 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All Kicker Speakers are covered by a limited 1 year warranty against defects in material or workmanship. All Kicker Amplifiers are covered by a limited 2 year warranty against defects in material or workmanship.
A A A A. Take the MRB3 Remote and pass the din cable through the dash kit panel. Once MRB3 remote is laying flat on the dash panel pass (2) M3 Screws through the remote and kit panel. Flip the kit around and use (2) M3 washers and (2) M3 Nuts to secure the MRB3 down into position. Do not over tighten the nuts, this can cause damage to the dash kit panel. B B B B. Loosley assemble the top mounting bracket to the dash kit panel using (2) M3 Screws.
5 Polaris RZR XP 1000 & 900 USB/AUX Input Port A A. Unscrew and remove the plastic nut from the port. Make sure to open the fuse holder and remove the fuse so the nut will fit through it. Crimp on the provided ring terminals on the ends of the (Red) Power and (Black) Ground wire. B B. Make sure all harness connectors are unplugged from the dash panel. Push out the factory 12v port. C C. Feed in the wires and cable through the factory 12v hole.
CONNECTING POWER & GROUND CABLE TO BATTERY A A A A. Zip tie all of the electrical cabling (factory and audio) along the center column away from the drive shaft B B B. Unscrew the factory nut on the negative battery terminal. Install the 2 ground cables to the screw on the ground battery terminal. Re-install the factory nut. C C C. Unscrew the factory nut on the positive battery terminal. Install the 2 power cables to the screw on the postive battery terminal. Re-install the factory nut.
