M A AN C I R E V A M H PWER C PO 5 O KIT I E D U A S A TS 3 X K ® ® R O SP pg 3 pg 11 pg 15 pg 19 pg 23 Disassembly, Wire and Amplifier Plate Installation Dash Kit Installation Underseat Subwoofer Installation Dash Speaker Pods Installation Cage Mount Speaker Pods Installation
X3-5K Can-Am Maverick X3 & X3 Max Kicker 5 Speaker Audio Kit WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All SSV Works Speakers are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered.
PANELS AND DASH DISASSEMBLY A A A. To remove the seat, use a 13mm socket and wrench to remove front (2) bolt and nut, and use a 18mm socket to remove (2) rear nuts and seat belt nut ( repeat on other seat) B B B B. Carefully unsnap center dash side panels by hand or with a panel removal tool. C C. Unscrew (2) T30 torx located on the center console panel under the dash. Use a panel tool to remove push pins on passenger side. 4 D D.
PANELS AND DASH DISASSEMBLY E E E E. Remove gas cover on the passenger side to expose a 10mm nut. Unscrew with a wrench and T30 torx driver. E2 E2 E2. Using panel removal tool unsnap (2) push clips on the driver and passenger side dash covers. Unscrew the (4) T30 screws on the passenger side, and (7) T30 screws on the driver side. F F. Remove fender well panel using a T30 driver (will need a10mm socket for the screw near the headlight) G G.
RUNNING AMP POWER CABLE AND SPEAKER WIRE WP-H16PG84-6 MRB3 Power Connector H H. Connect the MRB3 Power into the WP-H16PG84-6. Using the butt splice terminals on the WP-H16PG84-6, connect black to black and red to yellow. I1 I2 I. In this step you will be feeding all of the necessary wires from the top drivers side dash down the center dash column. Be sure to run all of the wires along side the factory cabling to avoid any moving parts.
INSTALLATION NOTES AMP TRAY MODIFICATION WHEN USED WITH AN AFTERMARKET ROLL CAGE 1. REMOVE THIS THREADED STUD BEFORE INSTALLAION OF THE AMP TRAY. GENTLY TAP OUT THE THREADED STUD WITH A HAMMER. BE CAREFUL NOT TO BEND THE BRACKET. 2.
AMP PLATE INSTALLATION K K K. From underneath driver side place amp plate between the two cross bars behind the steering wheel. L L. Make sure the threaded bolt on the amp plate goes through the factory hole located in the corner where the cage tubing connects. M M. Secure the amp tray to the vehicle using the supplied M6 nut and washer. * If your vehicle is equipped with an aftermarket cage, refer to page 2 for the installion of the amp tray. N N.
AMP PLATE INSTALLATION P1 P2 P. Route the front B-H1149 speaker harness towards the driver and passenger side of the vehicle and leave the 4 pin connector at the driver side of dash (P1). Route the passenger side speaker wire under the center dash panel all the way to the passenger side speaker location (P2). Q1 Q2 Q3 Q. Connect the B-H1149 to the front output of the 300.4 amplifer. Connect the B-H1151 to the rear output of the 300.4 amplifier. Connect the B-H1152 to the output of the 500.
USB/AUX INPUT PORT INSTALLATION S T S. Remove the (4) T30 torx on the front and inside of the glove box T. Remove push clips from underneath glove box. U V U. Pull up and remove the glove box. inside view V. Drill a 1” hole through the left side of the glove box for wiring inside view W outside view W X W. Unscrew and remove the plastic nut from the port. Make sure to open the fuse X.
X3-DM3 Can-Am Commander X3 Dash Kit for MRB3 SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All SSV Works Speakers are covered by a limited 1 year warranty against defects in material or workmanship.
A B. Locate the two dimples at the top of the dash. These dimples are actual screw bosses on the underside of the dash. A. Remove the factory rocker switches. C Line up base plate B C Drill pilot hole C Drill 1/2” hole C. Rest the X3-DM3 base plate on the dash. Line up the two outside screw holes with the dimples of the dash. Do not screw the kit in yet. While holding the base plate down to the dash, use the center hole on the base plate to drill your 1/8” pilot hole.
F F F. Now that the MRB3 remote is mounted to the dash kit route the din cable through the base plate so that it drops into the dash. Pull the din cable all the way through until the X3-DM3 Top Panel rests on the Base Plate. G G G. Using (2) #7 screws, secure the top of the Top Panel to the Base Plate. H H. Refer to the MRB3 manual for wiring instructions.
X3-US10K 2016+ Can-Am Maverick x3 10” Under Seat Enclosure SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship.
B A A. Apply the foam strips to the inside right, left and top side of the enclosure. C B. Using the supplied M6 screws and washers, screw the DD-brackets to the bottom right and left side of the enclosure. C C C. Remove the factory 10mm nut and bolt from the brake line. Place the washer on top of the factory bracket and push the long M6x25mm screw through the top. Then attach the brake line, spacer, washer and nut. T hen hand tighten. D D.
F1 F2 F3 F. Place B-Bracket to the left side of the enclosure and slide the tab underneath the enclosure. (F1) Line up the 2 screw holes and proceed to hand thread the M6 screws and washers. Use a T30 Torx bit to tighten screws. Repeat for the right side. (F2) Line up the top of bracket A and B with the holes on the factory seat brakcet. Screw in the M6 screw with the large washer (F3). WIRING INSTRUCTIONS PXA 500.
X3-F4 2017+ Can-Am Maverick x3 & x3 Max 4” Speaker Dash Pods SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship.
A B B. Pry off the (4) clips on the base under the empty space for the speaker A. Remove the top dash panels on the driver (7 screws with 2 clips) and passenger side (5 screws with 2 clips). C1 C2 D1 D2 C. Using a utility knife, cut off the (4) tabs flush to the panel D. Drill a hole using a 1/4” drill bit at the factory dimple marks (as shown above) on the outside dash panel around the speaker grille.
E F E. Place the acousic lens on top of the factory grille, line up the holes and insert the (2) top M6x1.0 (shorter) screws and washers. F. Place the speaker pod under the dash panel and line up the holes on the speaker pod with the (2) top screws and loosely mount the pod to the dash panel. G H G. Insert the M6x25mm screw by pushing it through the acoutic lens, dash panel and speaker pod. Secure screw using washer and 10mm nut. Now fasten the previous (2) M6x1.0 screws. H. Installation is complete.
US-C65K Universal Cage Mount 6.5” Speaker Enclosures SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered.
A A. Find the best orientation for the speaker on your bar and screw in the Set Screws in the OPPOSITE holes of where the clamp will install into. C B B. Loosely install the clamp base to the cage mount pod with the two (2) M6 hex head bolts and washers, place the cage mount pod in the desired mounting location on the vehicle. Once the ring adapter is in the desired position, tighten the two (2) bolts using a 8mm open wrench. C C.
D D. Take the B-H1150 rear speaker harness and plug into the B-H1151 rear extension harness. E E E. Route the rear speaker harness (B-H1150) along the factory wires in the engine compartment and pull up through the small space between the bed panel and cage tubing on both passenger and driver sides. WIRING INSTRUCTIONS PXA 300.
CONNECTING POWER & GROUND CABLE TO BATTERY A A A. Unscrew the factory nut on the negative battery terminal. Install the 2 ground cables to the screw on the ground battery terminal. Re-install the factory nut. B B B. Unscrew the factory nut on the positive battery terminal. Install the 2 power cables to the screw on the postive battery terminal. Re-install the factory nut. C C. Zip tie all wiring to the factory cables away from any moving parts. THIS CONCLUDES THE INSTALLATION PROCESS.
