CX AMPLIFIERS Owner’s Manual CXA360.4 Manual del Propietario | Español AMPLIFICADOR DEL LA SERIE CX.4 Benutzerhandbuch | Deutsch VERSTÄRKER DER CX.4-SERIE Manuel d’utilisation | Française AMPLIFICATEUR DE SÉRIE CX.
(fKICKER MODEL: CX.4-SERIES AMPLIFIERS OWNER’S MANUAL CXA360.4 Authorized KICKER Dealer: Purchase Date: Serial Number: WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at the same volume level. The threshold of pain is always an indicator that the sound level is too loud and may permanently damage your hearing.
VERTICAL MOUNTING amplifier end panel hex screws double-slotted bracket The CX amplifier has dual input sensitivity differential RCA inputs which will receive either high or low level signals from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the stereo RCA input on the end panel of the amplifier using the KICKER KISL as shown (make sure you set the CX amplifier’s input level switch to “HI”).
POWER WIRING GND REM +12V AMP1 AMP2 f ≤18” (45cm) ≤24” (60cm) +12V - external fuse battery remote turn-on (see page 6) -- -- bare-metal chassis ground bare-metal chassis ground 12V I f + ≤18” (45cm) external fuse For multiple amplifier installations where distribution blocks are used, each amplifier should have its proper-rated fuse, or breaker, installed between the amplifier and the distribution block within eighteen inches of the block, or on the distribution block if it provides for fusi
FOUR CHANNEL OPERATION minimum impedance of 2 ohms per channel L R AMP1 L AMP2 R BRIDGED OPERATION (MONO) minimum impedance of 4 ohms AMP1 AMP2 fjj STEREO-AND-MONO-SIMULTANEOUSLY (SAMS) OPERATION minimum impedance of 4 ohms bridged (mono) and 2 ohms per channel stereo AMP1 L AMP2 R 5
OPERATION FADER AMPt :!8ff AMP2 L 0 0 INPUT LEVEL :!h? I GAIN ~ I GAIN ~ AMP1 r---FREQ X-OVER 50-200Hz [CJ] OFF HI LO AMP2 BASS BOOST 0- 6 (dB) ~ ~ ~FREQ X-OVER 50-200Hz BASS BOOST 0- 6 (dB) REMOTE BASS LQJ ~ ~ 0 audio inputs Automatic Turn-On Selection: The CX series offers two automatic turn-on modes; +12V and DC Offset.
Bass Boost Control: The variable bass boost control on the side of the CXA360.4 amplifier is designed to give you increased output, 0–6dB, at 40Hz. The setting for this control is subjective. If you turn it up, you must readjust the input gain control to avoid clipping the amplifier. Remote Bass-CXARC (not included): With the CXARC remote bass level control, you have the ability to attenuate the output level of AMP2 remotely (AMP2 must be in LO-PASS X-OVER mode).
Alternator noise-whining sound with engine’s RPM? nCheck for damaged RCA (or speaker input) cable oCheck the routing of RCA (or speaker input) cable pCheck the source unit for proper grounding qCheck the gain settings and turn them down if they are set too high. Ground Noise? KICKER amplifiers are engineered to be fully compatible with all manufacturers’ head units. Some head units may require additional grounding to prevent noise from entering the audio signal.
ELECTRONICS LIMITED WARRANTY When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase with receipt. If this product is identified as “Refurbished” or “B Goods”, the warranty is limited to a period of THREE (3) MONTHS from the date of original purchase. In all cases you must have the original receipt.
HOW LONG WILL IT TAKE? KICKER strives to maintain a goal of one-week turnaround for all electronics (amplifiers, crossovers, equalizers, etc.) returns. Delays may be incurred if lack of replacement inventory or parts is encountered. Failure to follow these steps may void your warranty. Any questions can be directed to the KICKER Customer Service Department at (405) 624-8510. Contact your International KICKER dealer or distributor concerning specific procedures for your country’s warranty policies.
©2018 Stillwater Designs
4Ω 2Ω 1Ω 0.5Ω IMPEDANCE 4Ω 2Ω 1Ω 0.5Ω IMPEDANCE 4Ω 2Ω 1Ω 0.5Ω IMPEDANCE 80.00V 56.57V 40.00V 28.28V 1600W 1500W 77.46V 54.77V 38.73V 27.39V 44.72V 31.62V 22.36V 15.81V 500W 400W 40.00V 28.28V 20.00V 14.14V 14.14V 10.00V 7.07V 5.00V 50W 13.42V 9.49V 6.71V 4.74V 45W V=SQRT(WATT*IMPEDANCE) 75W 100W 17.32V 12.25V 8.66V 6.12V 20.00V 14.14V 10.00V 7.07V 700W 800W 52.92V 37.42V 26.46V 18.71V 56.57V 40.00V 28.28V 20.00V 2000W 2400W 84.85V 60.00V 42.43V 30.00V 89.44V 63.25V 44.72V 31.
46CXA360.
