Owner’s Manual Manual del Propietario Manuel d’utilisatio Benutzerhandbuch KM604 Coaxials Altavoz Coax KM KM Koax-System Haut-parleurs Coaxiaux KM select language seleccione el idioma choisir la langue sprache auswählen 49KM604-c
Contents Overview........................... 3 Specifications.............................. 4 Installation......................... 5 Wiring Configuration..................... 5 LED Wiring Configuration............. 6 Mounting..................................... 7 Warranty........................... 9 International Warranty.......
Overview IMPORTANT SAFETY WARNING PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN A DISTORTED, CLIPPED OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM TO OVERHEAT, POSSIBLY CATCHING FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4 INCHES (10CM) OPEN VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.5CM) CLEARANCE BETWEEN THE FRONT OF THE SPEAKER AND ANY SURFACE.
Specifications KM Component Speakers KM604 Woofer [in, mm] 6-1/2, 165 Tweeter [in, mm] 1/2, 13 Rated Impedance [Ω] 4 Peak Power Handling [ Watts] 150 Recommended Amplifier Power [Watts RMS] 15-50 Sensitivity [1W, 1m] 90 Frequency Response [Hz] 35–21k Tweeter Magnet Material Neodymium Tweeter Dome Material PEI (polyether imide) Tweeter Design Balanced Dome Midrange/Tweeter Surround Material UV Treated Cloth Woofer Cone Material Polyproplene Woofer Surround Material Santoprene Moun
Installation Wiring Configuration We recommend using 16 gauge (or larger) wire. The KM Speakers are rated at 4 ohms and work with any source unit or amplifier designed to operate at a 4 ohm load. Make sure your source unit or amplifier is rated for 4 ohm operation. Carefully place the speaker wire in a location that is clear of standing water and moving components of the boat. Connect the speaker wire to the speaker terminals. At least two amplifier channels are needed for stereo operation 1.
LED Wiring Configuration When hard-wiring the LED lighting, the black lead is +12V and the blue lead is ground. 1. Connect the black LED wire to the positive terminal of the battery. Place a 2-amp fuse (not included) no further than 7” away from the battery terminal. Install a switch (not included) on the black LED wire between the fuse and the speaker, so the LED’s can be turned off. Without a switch to turn them off, they will always be on. 2.
Mounting The KICKER KM Speakers are designed for free-air applications and do not require a sealed enclosure for optimum performance. It is important to isolate the sound coming from the front of the speaker from the sound radiating from the back of the speaker. The sound produced by the KM coaxials is directional. Find the best location for stereophonic sound. If necessary, add more KM coaxial speakers to the system to help distribute and balance the soundstage.
Secure speaker to desired location.
Warranty When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase with receipt. If this product is identified as “Refurbished” or “B Goods”, the warranty is limited to a period of THREE (3) MONTHS from the date of original purchase. In all cases you must have the original receipt.
The RMA number must be clearly marked on the outside of the package. Please return only defective components. The return of functioning items increases your return freight charges. Nondefective items will be returned freight collect to you. For example, if a subwoofer is defective, only return the defective subwoofer, not the entire enclosure.
