LIVIN’ LOUD D DX AMPLIFIER DX600.5 English Version Versión Español Amplificador del la Serie DX.5 Deutsche Version Verstärker der DX.5-Serie Version Francaise Amplificateur de série DX.5 2011 DX 5-Channel Amps RevD.
DX.5-SERIES AMPLIFIERS OWNER’S MANUAL Authorized KICKER Dealer: Purchase Date: Model Number: DX600.5 Serial Number: PERFORMANCE Model: DX600.5 RMS Power, AMP1 and AMP2 @ 14.4V, 4 stereo, 1% THD+N @ 14.4V, 2 stereo, 1% THD+N @ 14.4V, 4 mono, 1% THD+N 40W x 4 75W x 4 150W x 2 RMS Power, SUB channel @14.4V, 2 mono, 1.5 % THD+N @14.4V, 4 mono, 1.5 % THD+N 300 x 1 150 x 1 Length, in. (cm) 18-1/8” (46) Height, in. (mm) 2-1/4” (57) Width, in.
The DX amplifier has dual input sensitivity differential RCA inputs which will receive either high or low level signals from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the stereo RCA input on the end panel of the amplifier using the KICKER ZISL as shown (make sure you set the DX amplifier’s input level switch to “HI”). Alternatively, the signal can be delivered to the amplifier using the low-level RCA outputs on the source unit.
FOUR CHANNEL OPERATION with SUBWOOFER minimum impedance of 2 ohms per channel (AMP1, AMP2, and SUB channels) 30A L+ 30A L– R+ R– SUB + AMP1 – ZXRC REMOTE BASS INSTALLATION (See page 5. ZXRC not included.) 1. mount the metal bracket 2. slide the housing until it snaps into the metal bracket back view REMOTE BASS 4 2011 DX 5-Channel Amps RevD.
OPERATION AUTO TURN ON +12V DC AUDIO OFFSET INPUT LEVEL LO HI GAIN 0 11 FADER OFF ON AMP1 X-OVER FREQ 50 200 XOVER OFF L R HI GAIN 0 11 AMP2 X-OVER FREQ 50 L 200 R XOVER OFF HI GAIN 0 L 11 R AMP1 AMP2 SUB signal in signal in sub signal in SUB X-OVER FREQ BASS BOOST 50 0 200 12 SUB INPUT AMP2 SUB REMOTE BASS Automatic Turn-On Selection: The DX series offers three different automatic turn-on modes that can be selected on the end panel; +12V, DC Offset, and Audio
TROUBLESHOOTING If your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is a Power Protection LED on the side power panel of your Kicker DX series amplifier. Depending on the state of the amplifier and the vehicle’s charging system, the LED will glow either Red or Green.
KICKER will now provide a threeyear warranty with all DX-Series Amplifier purchases paired with a qualifying KICKER Installation Kit* . This extends the standard warranty by an additional year. Amplifier and Kit must be purchased from an Authorized KICKER Dealer. KICKER DX amplifier success is currently at an unheard-of rate, making the extended warranty program even more beneficial to you. Using poor-quality, under-spec wiring kits will impede DX amplifier performance.
AMPLIFICADOR DE LA SERIE DX.5 MANUAL DEL PROPIETARIO Distribuidor autorizado de KICKER: Fecha de compra: Número de modelo del amplificador: DX600.5 Número de serie del amplificador: RENDIMIENTO Modelo: DX600.5 Potencia RMS, AMP1 y AMP2 @ 14.4V, 4Ω stereofónico, 1% THD+N @ 14.4V, 2Ω stereofónico, 1% THD+N @ 14.4V, 1Ω monofónico, 1% THD+N 140W x 1 275W x 1 500W x 1 Potencia RMS, SUB canal @ 14.4V, 4Ω monofónico, 1.5% THD+N @ 14.4V, 2Ω monofónico, 1.5% THD+N 300 x 1 150 x 1 Largo, in.
El amplificador DX tiene entradas RCA diferenciales de doble sensibilidad de entrada que reciben señales de alto nivel o bajo nivel de la unidad fuente del sistema estereofónico del automóvil.La señal se puede llevar al amplificador desde las salidas de altavoz de alto nivel de la unidad fuente. Fije el selector de nivel de entrada del panel de extremo del amplificador en la posición de alto (HI).
FUNCIONAMIENTO POR CUATRO CANALES CON SUBWOOFER impedancia mínima de 2 ohmios por canales (AMP1, AMP2, y SUB canales) 30A L+ 30A L– R+ R– SUB + AMP1 – ZXRC CONTROL REMOTO DE BAJOS INSTALACIÓN (no incluido ZXRC. Vea la página 12) 1. monte el soporte de metal 2. deslice el alojamiento hasta que encaje en el soporte de metal vista desde atrás REMOTE BASS 10 2011 DX 5-Channel Amps RevD.
AUTO TURN ON +12V DC AUDIO OFFSET INPUT LEVEL LO HI GAIN 0 11 FADER OFF ON AMP1 X-OVER FREQ 50 200 XOVER OFF L R HI GAIN 0 11 AMP2 X-OVER FREQ 50 L 200 R AMP1 AMP2 señal de entrada señal de entrada XOVER OFF HI GAIN 0 L 11 BASS BOOST 50 0 200 12 SUB INPUT R SUB SUB X-OVER FREQ AMP2 SUB REMOTE BASS señal de entrada sub FUNCIONAMIENTO Selección de Encendido Automático: La serie DX ofrece tres modalidades de encendido automático que se pueden seleccionar en el pan
Control de Crossover: El crossover variable ubicado en la parte de arriba del amplificador permite ajustar la frecuencia de crossover de 50 a 200 Hz. La configuración de este control es subjetiva; 80 Hz es un buen punto de partida. Control Remoto de Bajos-ZXRC (no incluido): Con el control remoto de bajos, el nivel de salida del amplificador se puede controlar a distancia. Para montar el control remoto de bajos, atornille el soporte de metal en el lugar escogido.
Nota importante: Los altavoces modernos de alto rendimiento tienen menos resistencia a la CC que los de antes. Los altavoces de componente o coaxiales de KICKER tienen un valor nominal de 4Ω (algunas resistencias de CC pueden llegar a 3Ω) y funcionan con cualquier unidad fuente o amplificador diseñado para funcionar con 4Ω de carga. Si desea utilizar dos altavoces de componente o coaxiales de KICKER en un solo canal de su amplificador, conéctelos en serie.
VERSTÄRKER DER DX.5 SERIE BENUTZERHANDBUCH Autorisierter KICKER-Händler: Kaufdatum: Verstärker-Modellnummer: DX600.5 Verstärker-Seriennummer: LEISTUNG Modell: DX600.5 RMS-Leistung, AMP1 und AMP2 @ 14.4V, 4Ω stereo, 1% Gesamtklirrfaktor @ 14.4V, 2Ω stereo, 1% Gesamtklirrfaktor @ 14.4V, 1Ω mono, 1% Gesamtklirrfaktor 40W x 4 75W x 4 150W x 2 RMS-Leistung, SUB kanal @ 14.4V, 2Ω mono, 1,5% Gesamtklirrfaktor @ 14.
Der DX-Verstärker hat zwei RCA-Eingänge mit Eingangsempfindlichkeits-Differential, die entweder Hoch- oder Niedrigpegelsignale vom Autoradio empfangen. Kann das Signal mit den Hochpegel-Lautsprecherausgängen am Autoradio an den Verstärker übertragen werden. Stellen Sie den Eingangspegelschalter an der Endplatte des Verstärkers auf „HI“.
VIERKANALBETRIEB MIT SUBWOOFER Minimal impedanz von 2 Ohm pro Kanal (AMP1, AMP2, und SUB Kanäle) 30A L+ 30A L– R+ R– SUB + AMP1 – ZXRC BASSPEGEL-FERNBEDIENUNG INSTALLATION (ZXRC nicht inbegriffen. Siehe Seite 18.) 2. Schieben Sie das Gehäuse ein, bis es in der Metallhalterung einrastet. 1.
AUTO TURN ON +12V DC AUDIO OFFSET INPUT LEVEL LO HI GAIN 0 11 FADER OFF ON AMP1 X-OVER FREQ 50 XOVER 200 OFF L R AMP1 HI GAIN 0 11 AMP2 X-OVER FREQ 50 L 200 R AMP2 Signaleingang XOVER OFF HI GAIN 0 L 11 R SUB SUB X-OVER FREQ BASS BOOST 50 0 200 12 SUB INPUT AMP2 SUB REMOTE BASS Sub Signaleingang BETRIEB Automatische Einschaltung: Die DX-Serie bietet drei verschiedene automatische Einschaltmethoden, die an der Endplatte gewählt werden können: +12V, DC Offset und
Crossover-Regler: Die variable Crossover-Einheit an der Oberseite des Verstärkers ermöglicht es Ihnen, die Crossover-Frequenz zwischen 50 und 200 Hz einzustellen. Die Einstellung für diesen Regler ist subjektiv, aber 80 Hz wäre ein guter Ausgangspunkt. Basspegel-Fernbedienung-ZXRC (nicht inbegriffen). Mit der Basspegel-Fernbedienung können Sie den Ausgangspegel des Verstärkers per Fernbedienung kontrollieren.
Hinweis: Moderne Hochleistungslautsprecher haben einen geringeren Gleichstrom-Widerstand, als dies früher der Fall war. Die KICKER Koaxial- und Komponentenlautsprecher haben eine Impedanz von 4 Ohm (manche Gleichspannungs-Widerstände können auch nur 3 Ohm betragen) und können mit jedem Verstärker zusammenarbeiten, der auf 4 Ohm ausgelegt ist. Wenn Sie zwei KICKER Koaxial- oder Komponentenlautsprecher an einem Kanal Ihres Lautsprechers verwenden wollen, müssen Sie diese in Reihe schalten.
AMPLIFICATEUR SÉRIE DX.5 MANUEL D’UTILISATION Revendeur agréé KICKER : Date d’achat : Numéro de modèle de l’amplificateur : DX600.5 Numéro de série de l’amplificateur : PERFORMANCES Modèle: DX600.5 Puissance Efficace @ 14.4V, 4Ω stéréo, 1% THD+N @ 14.4V, 2Ω stéréo, 1% THD+N @ 14.4V, 1Ω mono, 1% THD+N 40W x 4 75W x 4 150W x 2 Puissance Efficace @ 14.4V, 2Ω mono, 1,5% THD+N @ 14.
L’amplificateur DX est doté de deux entrées RCA différentielles de sensibilité d’entrée qui reçoivent des signaux de haut ou bas niveau à partir de l’appareil source de la stéréo de votre voiture. Le signal peut être transmis à l’amplificateur en utilisant les sorties de haut-parleur de haut niveau sur l’appareil source. Réglez le commutateur de niveau d’entrée sur le panneau d’extrémité de l’amplificateur à la position « HI ».
FONCTIONNEMENT À QUATRE CANAUX AVEC CAISSON DE GRAVES impédance minimum de 2 ohms par canal (AMP1, AMP2, et le SUB canaux 30A L+ 30A L– R+ R– SUB + AMP1 – ZXRC TÉLÉCOMMANDE DU NIVEAU DES GRAVES INSTALLATION (ZXRC non inclus. Voir page 24.) 1. montez le support métallique 2. faites glisser le logement jusqu’à ce qu’il s’enclenche dans le support métallique Vue arrière REMOTE BASS 22 2011 DX 5-Channel Amps RevD.
AUTO TURN ON +12V DC AUDIO OFFSET INPUT LEVEL LO HI GAIN 0 11 FADER OFF ON AMP1 X-OVER FREQ 50 200 XOVER OFF L R AMP1 HI GAIN 0 11 AMP2 X-OVER FREQ 50 L 200 R AMP2 Entrée du signal XOVER OFF HI GAIN 0 L 11 R SUB SUB X-OVER FREQ BASS BOOST 50 0 200 12 SUB INPUT AMP2 SUB REMOTE BASS Sub entrée du signal UTILISATION Sélection de Mise sous Tension Automatique : La série DX est dotée de trois modes différents de mise sous tension automatique pouvant être sélectionnés
Commande de l’Augmentation des Graves : Située sur le haut de l’amplificateur, la commande de l’augmentation des graves variable permet d’augmenter la sortie de 0 à 12 dB à 40 Hz. Le réglage de cette commande est subjectif. Si vous l’utilisez, vous devez revenir à la commande de gain d’entrée et la régler pour éviter la distorsion par écrêtage du signal de l’amplificateur.
Bruit de fond ? Les amplificateurs KICKER ont été étudiés pour être entièrement compatibles avec les unités de tête de tous les fabricants. Certaines unités de tête peuvent exiger une mise à la masse supplémentaire pour éviter toute interférence avec le signal audio. Pour remédier à ce problème éventuel, il suffit dans la plupart des cas d’acheminer un fil de masse à partir des sorties RCA sur l’unité de tête jusqu’au châssis. Remarque : La résistance c.c.
ELECTRONICS LIMITED WARRANTY KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of THREE (3) MONTHS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer it is warranted for TWO (2) YEARS from date of original purchase with receipt. In all cases you must have the original receipt.
INTERNATIONAL WARRANTY Contact your International KICKER dealer or distributor concerning specific procedures for your country’s warranty policies. WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at the same volume level.
©2010 Stillwater Designs 2011 DX 5-Channel Amps RevD.